Determine the maximum kva rating as an autotransformer

Assignment Help Chemical Engineering
Reference no: EM131154346

A single-phase, two-winding, 10-kVA, 440:110- V, 60-Hz transformer is to be connected as an autotransformer to supply a load at 550 V from a 440-V supply. Draw a schematic diagram of the connections and determine:

(a) The maximum kVA rating as an autotransformer.

(b) The maximum apparent power transferred by conduction.

(c) The maximum apparent power transferred by electromagnetic induction.

Reference no: EM131154346

Questions Cloud

Disadvantages of low power factor : What are the disadvantages of low power factor? How can it be improved?
Determine the efficiency at this load : With a load of 0.8 power factor lagging, what kVA load can be supplied without exceeding the current rating of any winding? Determine the efficiency at this load.
Principle of a single -phase transformer : Explain the basic construction and working principle of a single -phase transformer.
Briefly describe the subspecialty area of police psychology : Identify and briefly describe the subspecialty area of Police Psychology. Summarize the reading that you completed
Determine the maximum kva rating as an autotransformer : A single-phase, two-winding, 10-kVA, 440:110- V, 60-Hz transformer is to be connected as an autotransformer to supply a load at 550 V from a 440-V supply.
Uses of a unijunction transistor : Give three uses of a Unijunction Transistor (UJT). Explain one use in detail.
State how you could apply this aspect at your current : Watch the video titled "Scripps," located in Week 5 of your Blackboard course. From the video, isolate one (1) of the many aspects of the Scripps recruitment and interview process that could be most attributable to Scripps' ample supply of registe..
Describe in detail the construction of a triode : Describe in detail the construction of a triode. To what use a triode may be put? How does it differ from a BJT?
What are active and passive components : What are active and passive components? Categorise the following components into these categories. Mettalized polyster capacitor, Preset Filter circuits, Audio-frequency chokes, FET, Vacuum tubes.

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Determine the velocity of sphere a after the collision

Sphere A is moving at a speed Vo=16 ft/s when it strikes sphere B which is at rest and the impact causes sphere B to break into two pieces, each of mass m/2 Knowing that 0.7s after the collision one piece reaches point C and 0.9s after the collisi..

  Question 1 two well of radius 18 inches are constructed in

question 1 two well of radius 18 inches are constructed in a confined aquifer 150 ft thick with hydraulic conductivity

  Compute the full-load speed

At full load and rated voltage, the line current is 40 A, and the flux is 5% less than its no-load value because of armature reaction. Compute the full-load speed.

  Carryover of liquid droplets

A vapor rate of 2500 kg/h is required and the vaporizer will operate at 6 bara. Size the vessel to restrict the carryover of liquid droplets. The liquid hold-up time need not be considered, as the liquid level will be a function of the thermal des..

  Calculate the amount of work exchanged between two cycles

A Carnot cycle operating between 600 °C and 25 °C absorbs 1000 kJ of heat from the high-temperature reservoir. The work produced is used to power another Carnot cycle which transfers 1000 kJ of heat from 600 °C to a reservoir at higher temperature..

  Define important information about vapor pressure

Important information about Vapor pressure, At the top of Long's Peak in the Rocky Mountains (a) what is the vapor pressure if boiling a container of eggs (without a lid) occurs

  Commonly used cubic equation of state

The Soave-Redlich-Kwong equation is a commonly used cubic equation of state, second in popularity only to the Peng-Robinson Equation of state. In this problem, just derive the two equations (7.66) given in the problem.

  Estimate the necessary tower diameter and the pressure drop

The gas density is 0.075 lb/ft3. The liquid density is 55 lb/ft3. The viscosity of the oil is 20 centipoises. Under these conditions, estimate the necessary tower diameter and the pressure drop through the tower as inches of water per foot of pack..

  Four stable isotopes of iron with mass numbers

There are four stable isotopes of iron with mass numbers 54, 56, 57, and 58. There are also two radioactive isotopes: iron-53 and iron- 59. Predict modes of decay for these two isotopes. (See Table 18.2.).

  What mass of h2 is produced

The hydrogen produced was successfully vented and no chemical explosion occurred. If 1.00  103 kg of Zr reacts, what mass of H2 is produced? What volume of H2 at 1.0 atm and 1000.°C is produced?

  Select a process variable

Select a process variable (pressure / temperature / level / flow) and conduct a literature survey to determine recent developments in process instrumentation field. Identify any one novel instrument and explain in detail the working of the instrument..

  What is the pressure at the azeotropic composition

At 50 °C the system acetone(1) and chloroform(2) forms an azeotrope with composition x1 = 0.416. What is the pressure at the azeotropic composition at 50 °C?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd