Determine the maximum horizontal distance that a projectile

Assignment Help Civil Engineering
Reference no: EM13559366

1.The roller coaster track consists of a circle in a vertical plane of radius 150m. find the magnitude of the total acceleration of the roller coaster if, at the time shown, the car is moving at 50 km/hr and is gaining speed at the rate of 0.4g

2.Determine the maximum horizontal distance that a projectile will have at a height of 60 m above the orgin if it is fired at an angle at 70 degrees from the horizontal with a velocity of 50 m/s

Reference no: EM13559366

Questions Cloud

Verify that sample mean and the sample variance converge : Write a computer program that generates a sequence of random variables from a normal distribution with mean 5 and standard deviation 2.
What is the final pressure in the device : A .2kg mass of argon gas fills a .05m^3 piston-cylinder volume at a pressure of 400 kPa absolute. The piston induced pressure is changed until the volume expands to twice its original value, while the temperature remains constant.
What is the velocity of the water at the exit for maximum : A suction device is being designed based on the Venturi principle to life objects in submerged water. The operating water temperature is 50C. The suction cup is located 1.3 m below the water surface, and the Venturi throat is located
Find the final temperature : A horizontal water jet impinges against a vertical flat plate at 25 ft/s and splashes off the sides in the vertical plane. If a horizontal force of 350 lbf is required to hold the plate against the water stream, determine the volume flow rate of the ..
Determine the maximum horizontal distance that a projectile : Determine the maximum horizontal distance that a projectile will have at a height of 60 m above the orgin if it is fired at an angle at 70 degrees from the horizontal with a velocity of 50 m/s
The plus sight and minus sight distances were kept approx : A differential leveling loop began and closed on BM bridge (elevation 103.895m). The plus sight and minus sight distances were kept approximately equal
How many extractions are required to decrease : Phenol is approximately 12 times more soluble in 1 volume of isopropyl ether than it is in 1 volume of water. How many extractions are required to decrease the concentration of phenol below 100 mg/L
What mass of pac must be placed in a contact basin : Toluene has contaminated a city's drinking-water supply. An activated carbon system has been constructed so toluene concentrations are treated to below specified regulatory levels. If the toluene concentration in the water supply is 1,000 ppb
How far did the piston move use interpolation : A piston cylinder is filled with .85 kg of refrigerant-134a at -10 degrees Celsius. The piston moves freely, and has a mass of of 12 kg and a diameter of 25 cm. Heat is added to the closed system (the refrigerant) until the temperature rises to 15 de..

Reviews

Write a Review

Civil Engineering Questions & Answers

  The existing flash mixer is about 20 years old and needs to

an existing water treatment plant is producing an average flow of 0.5 mgd. due to several limitations the plant only

  Velocity and acceleration of the flow

The volume flow rate of streams into the pipe is given by QA = 0.02t m 3 /s and that of stream B by QB = 0.008t 2 m 3 /s, where t is in seconds. The exit area of the pipe is 0.01m 2 . Find velocity and acceleration of the flow at exit at t = 1s.

  What is the mass flow rate of the refrigerant in kg per s

A vapor-compression refrigeration system, using Refrigerant 134a as the working fluid, has evaporator and condenser pressure of 1.4 bar and 12 bar, respectively.

  Determine what should the velocity for the model be

The prototype and model will both be in air, if the prototype has a velocity of 500 ft/s and a diameter of 30 ft, what should the velocity for the model be if the model diameter is 2 ft

  Estimate the minimum absolute pressure

When a fluid flows through a sharp bend, low pressures may developin localized regions of the bend. Estimate the minimumabsolute pressure (in psi) that can develop without causingcavitation if the fluid is water at 160 oF.

  Calculate the velocity and flow rate of acetone at the exit

A tank containing acetone at 20 oC has a drain pipe connected vertically at the bottom. The pipe is made of galvanized iron, 0.5 in NPS Schedule 40 with length L= 2m. The acetone depth in the tank is H= 5 m.

  Balancing of reciprocating engines

If the engine is mounted solidly on a rigid foundation, what is the alternating force amplitude transmitted? Assume the connection rod to be of infinite length.

  Find the magnitude of the force on one side of plate

A rectangular plate 5ft by 4ft is at an angle of 30 degrees with the horizontal, and the 5-ft side is horizontal. Find the magnitude of the force on one side of the plate and the depth of its center of pressure when the top edge is (a) at the wate..

  Compute the excess elastic energy e associated with this

A significant obstacle in the design of atomic weapons is theso-called delta phase instability (a type of mixed dislocation) inPu-239. This is the problem: We wish to construct a sphericalatomic bomb core out of pure delta phase (f.c.c.) Pu-239. A de..

  Determine the amount of cover over a culvert

A vertical curve of 600 ft in length is used to connect two tangents with the following locations: Tangent 1.- Point 1, Sta = 59+00, El = 1250.0' Point 2, Sta = 72+00, El = 1190.0' Tangent 2.- Point 1, Sta = 72+00, El = 1190.0' Point 2, Sta = 84+0..

  What are the concentrations of cl- and br-

AGNO3 is added to a solution containing 0.001 mol Cl- amd 0.001 mol Br- per liter. What are the concentrations of Cl- and Br- remaining when AgCl just begins to precipitate?

  What flow rate do you need to reduce the risk by 95 percent

A new sponge iron factory has an annual capacity of 100,000 tons/year of Iron production. Benzopyrene is produced during this process at a rate of 0.00006% of Iron produced.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd