Determine the maximum height to which the jet rises

Assignment Help Mechanical Engineering
Reference no: EM131144786

Q1. Water at 20°C, in the pressurized tank at 75 kPa gage, flows out and creates a vertical jet as shown. Assuming steady frictionless flow:

1) What is the pressure at point 1, 2 and 3?

2) What is the velocity at point 2?

3) Determine the maximum height H to which the jet rises.

4) Would the height to which the jet rises be more in case of a viscous fluid?

2425_Figure.png

Q2. For the horizontal pipe reducing section shown, D1 = 8 cm, D2 = 5 cm, and p2 = 101 kPa = patm. All fluids are at 20°C. If V1 = 5 m/s and the manometer reading is h = 58 cm, compute the following:

a) The pressure difference indicated by the manometer, in Pa (gage).

b) The velocity of the now at location 2, in m/s.

c) The total horizontal force resisted by the bolts in the flange.

2435_Figure1.png

Q3. A cylindrical water tank discharges through a well-rounded orifice to hit a plate, as shown in the Figure below. Water flows out through the orifice and impinges on the plate horizontally and splits equally in the vertical direction. The force F shown in the figure is in the horizontal direction. g acts along the vertical direction. The flow is inviscid. Assume that the direction and velocity of flow does not change as water flows from the orifice to the plate.

(a) Now assume that D (diameter of the tank) is much higher than d (diameter if the orifice/jet) such that the level of water in the tank (h) changes very little with time. If, under such circumstances, the force F required to hold the plate is 40 N, what is the depth h?

(b) Now assume that that D(diameter of the tank) is comparable to the d (diameter if the orifice/jet) such that the level of water in the tank (h) changes at the rate of 2.5 cm every second. If, under such circumstances, the force F required to hold the plate is 40 N. what is the tank diameter D?

Show the CV used to do the force balance.

35_Figure2.png

Q4. An incompressible liquid jet of velocity Vj and area Aj strikes a single 180° bucket on a turbine wheel rotating at a constant angular velocity U. The turbine has no angular acceleration. Neglect the effect of gravity. Also assume that the size of the bucket is very small compared to the turbine wheel of radius R and hence every point of the bucket can be assumed to be moving at the same velocity. Assuming steady state operation, the bucket to be a moving CV with constant velocity and the flow to be inviscid:

a) Find an expression for the power P delivered.

b) At what Ω is the power a maximum?

974_Figure3.png

Reference no: EM131144786

Questions Cloud

Prepare the adjusting journal entry : Prepare the adjusting journal entry on December 31. - Prepare the T-accounts for each account, enter the unadjusted balances, post the adjusting journal entry.
Why the long-run mpc is greater than the shortrun mpc : What are the similarities between the life-cycle and the permanent-income hypotheses? Do they differ in their approaches to explaining why the long-run MPC is greater than the shortrun MPC ?
Crime scene investigators to review areas : Brief review of these training areas along with a brief overview of your findings in a one- to two-page cover sheet for the work for your supervisor's review and approval.
What are blogs and how can marketers use them : What are blogs and how can marketers use them? What is source credibility, and what are two factors that influence our decision as to whether a source is credible? What is the difference between buzz and hype?
Determine the maximum height to which the jet rises : Water at 20°C, in the pressurized tank at 75 kPa gage, flows out and creates a vertical jet as shown. Assuming steady frictionless flow: Determine the maximum height H to which the jet rises
Discuss the importance of good business research : Provide a short paragraph explanation for each of the following questions: Discuss the importance of good business research. Please give an example. Discuss the contemporary trends and the nature of the research process.
What is effective rate stated rate and periodic rate : What is effective rate, stated rate and periodic rate?-escribe the relationship between APR, EAR and periodic rate.
What happens to this ratio after retirement : The text implies that the ratio of consumption to accumulated saving declines over time until retirement.
Reconcile the different theoretical perspectives : How would you reconcile the different theoretical perspectives – grace, accident, association, cognitive and personality – on creative problem solving? How is the index metaphor a re?ection of the cognitive approach to creative problem solving?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd