Determine the maximum deflection of point a

Assignment Help Civil Engineering
Reference no: EM131012387

The structure shown below is made of structural A-36 steel. The left post is a solid round steel member with a diameter of 6 inches. The right post is a square steel member which is 6 inches square. The horizontal member is a solid steel beam with a height of 12 inches and a width of 3 inches.

A) Determine the maximum load, P, that the structure can carry.

B) Determine the maximum deflection of point A as the failure load is approached.

C) Clearly show which member is causing the failure.

328_Transtutor.jpg

Reference no: EM131012387

Questions Cloud

What is the most common type of geothermal plant : Geothermal resources are divided into six categories. What are they and analyze them with pros/cons - what is the most common type of geothermal plant? Describe the principle behind Binary geothermal power plant.
Prepare an installment payments schedule : Show how the total mortgage liability should be reported on the balance sheet at December 31, 2014. ( Talkington Electronics balance sheet December 31 2014 )
Which company had higher operating leverage : In its 2008 annual report, The Coca-Cola Company reported sales of $31.9 billion for fiscal year 2008 and $28.9 billion for fiscal year 2007. The company also reported operating income (roughly equivalent to EBIT) of $8.4 billion and $7.2 billion in ..
What is the balance in the column after these payments : Assume the following: Payment #1 totals $1,600 ($1,200 principal and $400 interest expense); Payment #2 totals $1,600 ($1,300 principal and $300 interest expense); and the remaining principal balance before these two payments is $50,000. If the amort..
Determine the maximum deflection of point a : The horizontal member is a solid steel beam with a height of 12 inches and a width of 3 inches. Determine the maximum load, P, that the structure can carry.
Define a teratogen : Define a teratogen and then choose either the embryonic period or the fetal period and describe the effect a teratogen may have during that period
Equal nominal annual payments : You buy a car, and take out a loan for $14,000 that has equal nominal annual payments over the next five years. The real rate of return on the loan is 4.3%, and the annual inflation rate is 2.6%. What will the payments be?
Savings account that earns effective annual interest rate : You plan to invest $600 in your savings account this year and then you intend to increase the amount that you invest by 3% each year. If you invest in a savings account each that earns an effective annual interest rate of 7% how much money will you h..
Journalize the entry to record the transaction on june : Journalize the entry to record the payment of the second installment the following June 30.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the minimum removal efficiency of the electrodialys

An electrodialysis is used to treat a stream of 125 m3/d produced water with a salinity of 13,000 mg/L NaCl before the produced water is discharged to the river with the flow rate of 5 million L/d and salinity of 20 mg/L NaCl

  Find the final temperature using the three methods

It is desired to compare the results of property predictions for water near or in the saturation region using (a) the ideal gas equation, (b) the compressibility chart and

  Determine the actual concentration for both pollutants

An industrial off gas steam must be treated for both particulates and SOx. The gas is at 1500 degrees F and 1.5 atm of pressure containing 80 mg/cubis meter of particulates and 25 mg/cubic meter of SOx. A two unit system is bring considered consistin..

  Depreciation using straight line-double declining balance

Calculate the depreciation using straight-line, double-declining-balance (DBB), and MACRS (current IRS regulation) methods; and tabulate the depreciation schedule.

  Find the air pressure at the height on air pressure

The efficiency of the engines of subsonic airplanes depends on air pressure and usually is maximum near about 36,000 ft. Find the air pressure y(x) at this height. The rate of change y(x) is proportional to the pressure

  How much water do produce for the municipality per day

A municipal water plant has four filters that are each 20 ft long by 15 ft wide by 5 ft deep. The demand for water requires that they only operate, on average, three filters per day at a loading of 3 gallons per min / ft^2.

  Determine how much pressure is developed in the system

A multiple-piston hydraulic jack has two output pistons, each with an area of 250 cm^2. The input piston, whose area is 25 cm^2, is concerned to a lever that has a mechanical advantage of 9:1.

  Compute its original length if the deformation is totally

A cylindrical specimen of a metal alloy is stressed in compression. if its original and final diameters are 40.00mm and 40.10mm respectively, and its final length is 120.00mm

  Determine the tension-compression boundary

Determine the tension-compression boundary for an axially loaded I-beam

  What is the mach number of the flow around the aircraft

A jet aircraft flies at a speed of 600 mph at an altitude of 40,000 ft. The atmosphere is the standard atmosphere. (1) What is the air pressure outside the aircraft (2) What is the Mach number of the flow around the aircraft

  Classify the soils using the given grain size distribution

Classify the following soils using the given grain size distribution (ASTM system) and Atterberg Limits data:

  Estimate the theoretical fracture strength of a brittle

Estimate the theoretical fracture strength of a brittle material ifit is known that fracture occurs by the propagation of anelliptically shaped surface crack of length

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd