User Account

All Pages

Determine the maximum bit rate possible

Assignment Help Electrical Engineering
Reference no: EM132050105

A 0.88 m optical communication system transmits data over a 10 km single mode fibre by using 10 ns pulses. The dispersion parameter of the fibre is D = 80 ps/(km-nm). The LED optical source has a spectral width of 51 nm. Determine the maximum bit rate possible.

Reference no: EM132050105

Questions Cloud

What is the purpose of the adc : What is the purpose of the ADC? How do you interface to the different configurations?
How do the following properties change if everything : In a p+ -n junction, the n-doping Nd is quadrupled. How do the following properties change if everything else remains unchanged?
Calculate the power loss in the wires : Total resistance of the wires b. Current through the solenoid c. Voltage across solenoid d. Calculate the power loss in the wires
What are the peak and rms supply voltages : What power is dissipated by an electric range element that has a resistance of 65 O when drawing a current of Ipeak = 5A?
Determine the maximum bit rate possible : The LED optical source has a spectral width of 51 nm. Determine the maximum bit rate possible.
Sketch the system response : A system is described by an impulse response h(t) = delta(t - 2) - delta(t + 4) Sketch the system response y(t) = h(t) * f(t)
Sinusoidal voltage source that supplies the parallel : How much power is provided by a 100 V (rms), 50Hz sinusoidal voltage source that supplies the parallel combination of the 10 O resistor and 3mH inductor?
Number of bytes required to store : If there are 16 high contrast levels of gray, the number of bytes required to store this image is:
What additional emerging materials and technologies : What additional emerging materials and technologies can be used to combat one of the following failures

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain tones input in to an amplifier

Tones Input In To An Amplifier, Suppose two tones are input in to an amplifier. The tones are pure sinusoids with one at frequencies 8GHz and the other at frequency 8.03GHz,(delta f =0.03GHz).

  Derive the logical functional expressions

Now we have the design that computes the correct duty cycle in the format Q1Q0 which represents 0% to 75%. Derive the logical functional expressions, and logic circuit. Draw the timing diagrams for S for both 25% and 75% duty cycles. At minimum, the..

  What happens to ensure the system is safe

Identify the standardized electrical symbols for the following common controls: indoor fan relay, humidistat, manual reset, and crankcase heater.

  What is the coefficient of coupling

What is the coefficient of coupling - Assume that the physical structure of these cou-pled coils is such that ρ1 = ρ2. What is the turns ratio N1/N2 if N1 is the number of turns on the 52 mH coil - Find the coefficient of coupling.

  Find the sinusoidal expression for the voltage

Find the sinusoidal expression for the voltage. In addition, sketch the v and i sinusoidal waveforms on the same axis.

  Can a tem wave propagate on this structure

Derive the solution (fields and cutoff frequency) for the lowest order TE mode of this structure. Assume the metal plates are infinitely wide. Can a TEM wave propagate on this structure

  How can the reactive power supplied or consumed by the ac ma

How can the real power flow through an ac-dc motor-generator set be controlled?

  What is the minimum current rating for the disconnect switch

An electric furnace has a minimum circuit ampacity rating of 50 A. What is the minimum current rating for the disconnect switch?

  Determine the capacitance of the capacitors per phase

Determine the capacitance of the capacitors per phase that are to be connected in delta across the terminals of the motor to raise the p.f to unity.

  What are the logic functions implemented by circuit

What are the logic 0 and logic 1 voltage levels? - What are the logic functions implemented by this circuit at vO1, vO2, and vO3?

  Obtain the expression for the electric potential

For the arrangement of a linear electric dipole consisting of point charges Q and at the points (0, 0,d/2) and (0, 0,-d/2), respectively, obtain the expression for the electric potential and hence for the electric field intensity at distances from..

  Create a partial truth table showing the requirements for

create a partial truth table showing the requirements for a seven-segment decoder to output a hexadecimal digit. this

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd