Determine the maximum bending stress on the outside surface

Assignment Help Civil Engineering
Reference no: EM13306497

A hollow cylinder with an inside diameter of 30 mm and outside diameter of 40 mm acts as a cantilever beam. A concentrated moment is applied to the free end. Determine the maximum bending stress on the outside surface of the cylinder and the maximum bending stress on the inside surface of the cylinder.

Reference no: EM13306497

Questions Cloud

Determne the angular velocity at the instint theta : When theta=0 degrees , the assembly is held at rest, and the torsional spring is untwisted. If the assembly is released and falls downward, determne the angular velocity at the instint theta=90.
Find the change in the period of the heated pendulum : A simple pendulum consists of a ball connected to one end of a thin brass wire. find the change in the period of the heated pendulum
What must average speed of the car be during the last min : During the first 18 minutes of a 1 hour trip, a car has an average speed of 11 m/s. What must the average speed of the car be during the last 42 minutes of the trip to be if the car is to have an average of 21 m/s for the entire trip
Determine the angular acceleration of this turntablr : When the power is turned off on a turntable spinning at 67.0 rpm, you find that it takes 13.0 revolutions for it to stop while slowing down at a uniform rate. What is the angular acceleration (in rad/s^2), of this turntable
Determine the maximum bending stress on the outside surface : A concentrated moment is applied to the free end. Determine the maximum bending stress on the outside surface of the cylinder and the maximum bending stress on the inside surface of the cylinder.
Determine how far apart must two diameter tanks be placed : How far apart must two 18 , diameter tanks be placed such that their stress overlap is not greaer than 10% of the contact stress at depths of 10, 20, and 30 m
Determine how much energy does it deliver into a home : A heat pump has a coefficient of performance of 3.85 and operates with a power consumption of 6.88 x 103 W. How much energy does it deliver into a home during 2 h of continuous operation
Find the probability christian wont pick out a grey tie : Christian is picking out ties for a business trip. Anastasia knows from experience that Christian has a 50% chance of picking a grey tie. Find the probability Christian won't pick out a grey tie until the 3rd or 4th tie.
How is the minimum radius affected if the b decreases : Roller coasters are designed so that the riders will not experience more than a certain level of g-force during the ride. (The rider would experience B g's if hte normal force were Bmg where B is a numbe

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the net rate of flow of linear momentum

Determine the net rate of flow of linear momentum through the control surface.

  Magnitude of shaft work obtained from the turbine

If the amount of heat transfer in the HE unit is 2460 kJ per kg of steam, what is the magnitude of shaft work obtained from the turbine in kW?

  Find the magnitude of the particles position and velocity

The position of a particle P moving in the horizental plane is described by r(t)= (5t^2 i +2te^0.1t j) m. Find the magnitude of the particle's position, velocity, and acceleration at time t=2 sec.

  What is the magnitude of the force s if the angle is given

A pile resists the tension developed by three stay cables for a major tent (Membrane) Structure. Assuming no bending is desired in the pile (no resultant horizontal component), what is the magnitude of the force S if the angle \thetaS = 30 degrees

  What is the axial force in member hj

The frame shown is used to support high-tension wires. If W = 200 lb, b = 3 ft, a = 30°, what is the axial force in member HJ?

  Civil engineering - structure design

Structural design of reinforced cast in - place concrete - Structure design

  Introduction to consolidation settlements

Include immediate and consolidation settlements, but ignore secondary compression. In your calculation, use three sublayers with thicknesses of 4 ft, 8 ft and 16 ft for the top, middle and bottom layers. Ignore any settlement caused by the dense s..

  Determine the moment of the force about point b

A force, 90 N in magnitude, is applied to control rod AB as shown. Knowing that the length of the rod is 225 mm, determine the moment of the force about point B by resolving the force into components along AB and in a direction perpendicular to AB..

  Find if vehicle is reasonable claim or a gross exageration

an average vehicle puts out nearly 20 lbm of carbon dioxide into the atmosphere for every gallon of gasoline it burns, thus one thing we can do to reduce global warming is to buy a vehicle with higher fuel economy.

  Determine whether these conditions are true or false

Determine whether these conditions are true or false.

  Draw p-v dia for pure component and label appropriate point

Draw a P-V diagram for pure component and label appropriate points such as superheated region, isothermal line, etc.

  Importance of mineral identification in applications

What are minerals? Sketch different types of mineral crystal forms and list different types of rock forming minerals. Describe with examples the importance of mineral identification in engineering applications.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd