User Account

All Pages

Determine the maximum allowable tensile force on the bar if

Assignment Help Mechanical Engineering
Reference no: EM13645227

A structural lin that is 3 in. wide and 0.5 in. thick is to have a factor of safety of 2 relative to its yield strength of 36 Ksi. (a) Determine the maximum allowable tensile force on the bar. (b) if the link is allowed to elongate by no more than 0.05 in. prior to reaching the maximum allowable tensile force, determine the maximum length of the link.

Reference no: EM13645227

Questions Cloud

Find a total strain corresponding to yield strength b what : in a tensile test for an alloy used for ballistic-missile launch tubes on boomer submarines the yield strength was
Suppose that a box contains 5 candies in which 2 of them : suppose that a box contains 5 candies in which 2 of them are sugar-free. you select two candies and eat them. find the
A if the block travels a distance of 45m along the surface : a block of mass m5.0kg is pulled along a rough horizontal surface by a rope as sketched. the tension in the rope is 40n
In the us it is estimated that an average person makes 4 : in the u.s. it is estimated that an average person makes 4 visits a year to the doctors office.a what is the mean and
Determine the maximum allowable tensile force on the bar if : a structural lin that is 3 in. wide and 0.5 in. thick is to have a factor of safety of 2 relative to its yield strength
A projectile is fired with a speed of v 60 ms at angle of : a projectile is fired with a speed of v 60 ms at angle of 60 degrees. a second projectile is then fired with the same
What is the probability that 2 workers will retire at 65 : approximately 80 of workers are sure that they will be able to retire at 65 years of age. suppose 10 workers are
Atemperature difference of 300c is imposed across a low : a temperature difference of 300c is imposed across a low density particle board of 10 cm thickness. the thermal
A bookshelf contains 20 textbooks for different subjects : a bookshelf contains 20 textbooks for different subjects. among those 10 of them are used ones and 10 of them are brand

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Estimate by what percent the average air-water density is

the presence of raindrops in the air during a heavy rainstorm increases the average density of the air-water mixture.

  Calculate the initial stress for each assembly which of the

bar a was manufactured 2mm shorter than bar b due to an error. the attachment of these bars to the rigid bar would

  Calulate the temperature change in the block after it comes

an iron blok m1kg initialy held stationary is dropped form a 100 m height. it strikes the groud and is assumed to be

  What is the overall accuracy error systematic error discuss

a steel bearing is known to have a true diameter of 0.4982 in. in the laboratory you use a micrometer that is supposed

  Define and design a hollow steel shaft to transmit

Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.

  Find the specific flow exergy in and out of the steam

find the specific flow exergy in and out of the steam turbine in example 9.1 assuming an ambient at 293 k. use the

  If the rate of heat loss from the pipe is to be kept around

consider a hot-water pipe 12-m in length and 8-cm in diameter. the pipe is to be buried in the soil below the ground

  A closed system contains 2-kg of air undergoes an

a closed system contains 2-kg of air undergoes an isothermal process from 600 kpa and 200oc to 80 kpa. determine the

  A tunnel 150 m long 72 m high and 58 m wide with a flat

a tunnel 150 m long 7.2 m high and 5.8 m wide with a flat roof is to be constructed 60 m beneath the ground. the

  Determine a the air exit velocity to produce 5 lbf b the

an engineering student considers using a fan as a levitation demonstation. she plans to face the box-enclosed fanso the

  When loaded the gages read 1900 -700 and 240 300

an equiangular strain gage rosette is mounted on a free and unloaded surface of a part made of steel. when loaded the

  What is the velocity of the cart

what is the velocity of the cart when the bullet becomes embedded int he terget? during the firing, the man remains at the same position on the cart. neglect rolling resistance of the cart.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd