Determine the maximum acceleration of the camera

Assignment Help Civil Engineering
Reference no: EM13565004

A camera is packed in a box and surrounded by packing material. The box is dropped vertically onto a horizontal surface. The vertical velocity of the box at the time that it hits the surface is v= 5m/s. After impact the camera experiences an acceleration of a = -kx, where k is a constant and x is the compression of the packing material. If the packing material experiences a maximum compression of 30 mm, determine the maximum acceleration of the camera.

Reference no: EM13565004

Questions Cloud

Kinetic energy is translational and how much is rotational : When a pitcher throws a curve ball, the ball is given a fairly rapid spin. If a 0.15-kg baseball with a radius of 3.7cm is thrown with a linear speed of 48 m/s and an angular speed  of 42 rad/s, how much of its kinetic energy is translational and ..
What was the average power output used for this ride : The fastest that anyone has gotten to the top of a local mountain (elevation change of 3500 ft) is 44 minutes. Assume a weight of 160 lb for the bike and rider. What was the average power output used for this ride?
Find the resulting stress in the steel pipe material if the : If a manometer was used to measure the pressure drop and the fluid in the manometer was an oil with a specific gravity of 0.84, what would the vertical displacement of the oil menisci be for 1 inch of water pressure difference?
Find the dry unit weight of the sample : A soil has a total density of 1.80 Mg/m3. When fully dry, the soil has a density of 1.59 Mg/m3. The specific gravity of the solids is 2.57. Find the following soil parameters:
Determine the maximum acceleration of the camera : A camera is packed in a box and surrounded by packing material. The box is dropped vertically onto a horizontal surface. The vertical velocity of the box at the time that it hits the surface is v= 5m/s.
Show that the car must have exceeded the speed limit of 55 : highway patrol officer, you are patricipating in a speed trap. A car passes your patrol car which you clock at 55 mph. One and a half minutes later, your partner in another patrol car situated two miles away from you
Find the magnitude and location of the resultant hydrostatic : A circular hatch is located in a sloping wall of a water-storage reservoir, where the wall slopes at ? = 35° to the horizontal, the radius of the hatch R is 840 mm, and the center of the hatch yC is 3 m below the water surface (measured along the slo..
How many inch diameter rivets are required to transmit : How many 3?4-inch diameter rivets are required to transmit 55,000 lb from the two angles to the gusset plate if the allowable shear stress in the rivets is 15,000 psi? Assume each rivet carries the same amount of load.
Determine the shear stress in the water : Would it be more efficient to use the method of section on the diagonal cross member part of the truss or do you have to use the method of joints to determine other forces first?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum bending stress that will occur

Determine the maximum bending stress that will occur in a timber beam of rectangular section 250mm x 80mm when a bending movement of 500N is applied about the x-x axis

  How much would the diver need to weigh to cause

A 200 pound man stands at the end of a 16 foot diving board (point C) with a pin at (A) and a roller located 6.695 ft away from A at point (B). The hollow diving board is made of aluminum

  Determine what is the balance delay for the solution

A proposal has been submitted to replace a group of assembly workers, each working individually, with an assembly line. The following table gives the individual work elements. The demand rate for this job is 1600 units/week (assume 40h/week)

  What is the lowest grade possible for the constant grade

A tangent section of highway has a -1.0 % grade and ends at station 0+145 and elevation 25m. it must be connected to another section of highway that has a -1.0 % grade and that begins at station 1+345 and elevation

  Find e in terms of b and h to have one type of normal stress

For arectangular section (b(width) x h(thickness) that is subjected to aforce P that is applied at an eccentricity (e) measured from thecenter of area of the rectangle in the h(thickness)direction

  What is the corresponding amplitude of the acceleration

calculate the amplitude F0 of the sinusoidal excitation force that is necessary to produce a steady-state vibration with a velocity amplitude of 10 m/s at resonance. what is the corresponding amplitude of the acceleration

  Is this level dangerous to the fish population

A lake has a volume of 750,000 m3 (dimensions 15 m deep, 100 m wide, and 500 m long) and behaves as two completly mixed cells. Cell 1 makes up 40% of the lake ( dimensions 15 m deep, 100 m wide, and 200 m long) cell 2 makes up 60% of the lake (dimens..

  Calculate concentration of oxygen in water in equilibrium

Calculate the concentration of oxygen in the water in equilibrium (in mg/L) with the atmosphere near La Paz, Bolivia (3650 m), at 20 degrees Celcius.

  How long will it take for the pce to reach the well

The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)

  Derive mathematical relation describing calibration curves

An orifice meter was calibrated for dry air at T=90 F and P=1.3 atm. The calibration data are as follow: dp(inches of water): 0,0.5,1.0,2.0,3.0,4.0,5.0 Q(ft^3/minute): 0,2.0,3.0,4.2,5.0,5.5,5.8

  Find the probabilities that among 20 such lights

The If the probability that fluorecent light has a useful life of at least 500 hours is 0.85, find the probabilities that among 20 such lights

  Compute the ratio of the nominal flexural strength of the

Compute the ratio of the nominal flexural strength of the beam to the maximum service load moment, and compare your findings to the ACI load factors and strength reduction factor.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd