Determine the mass of the refrigerant in kilogram

Assignment Help Mechanical Engineering
Reference no: EM13706663

A 2-m^3 rigid tank contains refrigerant-134a vapor at 1.4 MPa, 180C. Determine the mass of the refrigerant in kilogram using:

a. the ideal gas law.

b. the real gas law.

c. the van der Waals equation of state.

d. the refrigerant-134a table.

e. what is the percent error if ideal gas law is used?

Reference no: EM13706663

Questions Cloud

Release more energy to completely condense the vapour : 2 kg of saturated vapour water and 8 kg of saturated vapour refrigerant-134a both at 100 kPa. Which substance will release more energy to completely condense the vapour? Explain
Find the exit temperature and the specific work : A turbine receives steam at 6MPa, 600 C with an exit pressure of 600 KPa. Assume the turbine is adiabatic and neglect kinetic energies. Find the exit temperature and the specific work
Determine the final fluid phase and the enthalpy change : Determine the internal energy change as saturated liquid steam at 60?F goes to a two phase mixture of quality 0.40 at 60?F. Provide answers in SI units. Determine the final fluid phase and the enthalpy change.
Cost of operating a large ship varies as the square : The cost of operating a large ship (CO) varies as the square of its velocity (v); specifically, CO = knv2 , where n is the trip length in miles and k is a constant of proportionality. It is known that at 12 miles/hour, the average cost of operation i..
Determine the mass of the refrigerant in kilogram : A 2-m^3 rigid tank contains refrigerant-134a vapor at 1.4 MPa, 180C. Determine the mass of the refrigerant in kilogram using:
Rate of heat transfer from plate to air by convection : A flat plate having an area of 10 m^2 and a temperature of 327 C is exposed to air at 27 C. the convective heat transfer coefficient is 15 W/m^3.C and the emissivity of the plate is 0.80.
The mass of piston on top of the tank : One side of a mercury manometer is connected to the top of frictionless piston-cylinder storage tank containing 1500 liters of oil, the other side is open to the atmosphere. The difference in the height of the column of mercury in the manometer is 90..
Determine the maximum length of a cylindrical walnut : It is known that a long log floats with its axis horizontal. A very short log, however, floats with its axis vertical. Determine the maximum length of a cylindrical walnut log 30 cm in diameter that will cause it to float with its axis vertical.
Calculate the conduction heat loss for the following wall : Calculate the conduction heat loss for the following wall: 15ft long, 8ft tall. Calculate for 8 hr, inside temperature at 78F and the outside temperature at 3F. Wall components from outside to inside are brick; 1.2cm(1/2 in.) plywood; wood studs, 5x1..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd