Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
to apply shock loading to an artillery shell, a 20kg pendulum A is released from a know height and strikes impactor B at a known velocity v (theta). impactor B then strikes the 1 kg artillery shell C. knowing the coefficient of restitution between all objects is e, determine the mass of B to maximize the impulse applied to the artillery shell c.
Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf. Use fc' = 3000 psi and fy = 60,000 psi. Make the slab thickness to ½-in. increments.
A 0.25 in diameter copper rod BC is securely attached between two identical 1 in diameter steel rods (AB and CD). Find the load P if the total elongation of the system is measured to be 0.0312 in. Esteel= 29,000ksi, Ecopper=17,000ksi.
Determine the differential settlement between the centre line of the ring beam and under the centre of beam. The inner and outer radii of the ring beam are 8m and 12m respectively.
During an experiment, the depth of a water flow in a flume is measured five times by using a ruler with 1/16-in division. The results from these measurements are 4.88 in, 5.06 in, 5.03 in, 5.13 in, 4.94 in. What is the instrumental error and what ..
Discharge from an orifice of 75mm diameter is 0.02 m^3/s under a constant head of 3 m. An external mouthpiece of the same diameter is installed that raises the coefficient of contraction from 0.63 to 1.0.
The flow in the river is 30ft^3/min and the first-order rate constant for disinfection is 6min^-1. 1)What kind of hydrodynamic model should you use. 2) write the mass balance equation for microorganisms in symbols at steady state. define symbols.
A circular hole of diameter 11.42 + and - 0.03 inches is cut out of the plate. Also, using the tolerances given, determine the minimum possible area of the top surface of the metal plate.
Describe the equation for discharging a water tank. Use: H= 2m, A_s= 1m^2, density water= 1000kg/m^3, K = 1kg hr^-1 m^-1/2 Mass flow in = 0 and mass flow out given by, Mass flow out = K z^1/2.
The temperature when the tires were in flated was 25 F. Assuming no change in air mass or volume, what is the temperature (F) in the tire after driving yesterday is a pressure on 44 psig was measured
Friction of the walker's shoes and rope are sufficient to cause the rope to have more tension on one side then the other. Neglecting the weight and any elastic deformations of the 20.1-m long rope, create a table using 1.0m increment for the range
A 4 X 8-ft solar collector has water circulating through it at the rate of 1.0 gallon per minute while exposed to sunlight with intensity 300 Btu/ft^2-hr.
The aquifer is inhomogeneous with K = 12+0.006x, where x =0 at point 1, and the piezometric heads at point 1 and 2 are 14.2 m and 18.8 m, respectively measured above the upper confining layer.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd