Determine the mass flow rate of refrigerant

Assignment Help Mechanical Engineering
Reference no: EM13906808

A large refrigeration plant is to be maintained at -15C, and it requires refrigeration at a rate of 100kW. The condenser of the plant is to be cooled by liquid water, which experiences a temperature rise of 8C as it flows over the coils of the condenser. Assuming the plant operates on the ideal vapor-compression cycle using refrigerant 134-a between the pressure limits of 120 and 700 kPa, determine

1. The mass flow rate of refrigerant

2. The power input to the compressor

3. The mass flow rate of the cooling water

Show the cycle on T-s diagram and state ALL assumptions and proper units.

Reference no: EM13906808

Questions Cloud

Assign service salaries and wages and to apply overhead : Prepare Engineering Contractors incurred service salaries and wages of $46,800 ($25,200 direct and $21,600 indirect) on an engineering project. The company applies overhead at a rate of 20% of direct labor. Record the entries to assign service salari..
Prepare the adjusting entry to recognize bad debt expense : A company had a 1/1/14 balance in the Allowance for Doubtful Accounts of $20,000. During 2014, it wrote off $14,400 of accounts and collected $4,200 on accounts previously written off. In T-account format, prepare the adjusting entry to recognize bad..
Hospitable co. provides the following sales forecast : Hospitable Co. provides the following sales forecast for the next four months:
Prepare a schedule of budgeted labor costs : Render Co. CPA is preparing activity based budgets for 2013. The partners expect the firm to generate bill able hours for the year as follows
Determine the mass flow rate of refrigerant : Assuming the plant operates on the ideal vapor-compression cycle using refrigerant 134-a between the pressure limits of 120 and 700 kPa, determine - The mass flow rate of refrigerant
Cause of the skin abnormalities in the graphics : Consider the abnormal physical characteristics you observe in the graphics you selected. How would you describe the characteristics using clinical terminologies? Explore different conditions that could be the cause of the skin abnormalities in the ..
Using the balance sheet equation : Using the balance sheet equation, show how each of the following six events would affect the balance sheet of Fernandez & Co. The sale of common stock to investors for $5 million in cash, the sale of a new bond issue to investors for $10 million cash..
The company plans to end each quarter with an ending : Rida, Inc., a manufacturer in a seasonal industry, is preparing its direct materials budget for the second quarter.
What would be the average tax rate for a person : What would be the average tax rate for a person

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the mass flow rate of steam through the diffuser

Steam at a pressure of 14.7psia and a temperature of 320deg F enters a diffuser inlet at a velocity of 500ft/s. The steam decelerates in the diffuser to a velocity of 100ft/s. The steam leaves the diffuser as saturated vapor at 240 deg F. The area of..

  Pipe for use within a chemical processing plant

What information do you need to know from the process engineering department to select suitable pipe? What information do you need to know from the structural engineering department to select suitable pipe?

  A solid 15-m-diameter sphere floats at the interface

i a solid 1.5-m-diameter sphere floats at the interface between water sg 1.0 and mercury sg 13.56 such that 30

  The temperature is 356degc the pipe has a circular

refrigerant r-22 enters a constant diameter pipe at a pressure of 10 bar a temperature of 20degc and a velocity of 2.20

  The sun warms the can and contents to a final tmperature of

a can of juice consists of .06 kg of aluminum and .355 liters of liquid. consider the contents to be saturated liquid

  Oxygen is flowing through a nominal 2 inch schedule 40

oxygen is flowing through a nominal 2 inch schedule 40 steel pipe pipe at a velocity of 10 fts. the oxygen is at a

  Outside atmospheric pressure

A piston/cylinder with cross sectional area of 0.01 m2 has a piston mass of 100 kg resting on the stops. With an outside atmospheric pressure of 100 kPa, what should the water pressure be to lift the piston?

  Find the required steam and cold water flow rates

Steam at 0.2 Mpa and 300 degrees Celsius is mixed with cold water at 20 degrees celsius and 0.2 MPa to produce 20 kg/s of saturated liquid water at 0.2 MPa. Find the required steam and cold water flow rates.

  Poly tropic coefficient and associated boundary work

A closed system contains 0.5 kg of nitrogen, initially at 150 KPa with a volume of 0.3 m^3. The system undergoes a poly tropic process resulting in the final state of 240 KPa and 100 C. Determine a) the poly tropic coefficient and b) the associated b..

  What can be said about the expected defect rate

Given that the nominal diameter (per print) is 15.00mm +/-0.10mm, what can be said about the expected defect rate?

  Measure the pressure inside

A mercury manometer (r = 13,600 kg/m3) is connected to an air duct to measure the pressure inside. The difference in the manometer levels is 15 mm, and the atmospheric pressure is 100 kPa.

  Liquid petroleum gas to fuel spark-ignition engines

It is proposed to use Liquid Petroleum Gas (LPG) to fuel spark-ignition engines. A typical sample of the fuel on a volume basis consists of: 70% propane C3H8; 5% butane C4H10; and 25% propane C3H6. The higher heating values of the fuels are 50.38 MJ/..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd