Determine the mass flow rate of dry air required

Assignment Help Mechanical Engineering
Reference no: EM131016939

In an industrial dryer operating at steady state, atmospheric air at 80°F, 1 atm, and 65% relative humidity is first heated to 280°F at constant pressure. The heated air is then allowed to pass over the materials being dried, exiting the dryer at 150°F, 1 atm, and 30% relative humidity. If moisture is to be removed from the materials at a rate of 2700 lb/h, determine

(a) the mass flow rate of dry air required, in lb/h.

(b) the rate of heat transfer to the air as it passes through the heating section, in Btu/h. Neglect kinetic and potential energy effects.

Reference no: EM131016939

Questions Cloud

Patrol for illegal immigration activities : Timothy Moher owns 440 acres of land on sugar land Michigan. Sugar land is located on St. Mary's River which marks the international border between Canada and the United States. Mohers land is 2 miles from Canada.
Find the lu factorization of the given matrix a : Find the LU factorization of the matrix A given below. Use this factorization to efficiently solve the systems of equations Ax→ = L(U x→) = bi→ for the bi→'s given below.
Economic crisis to afflict the united states : As of today the most severe economic crisis to afflict the United States economy is considered to be
Franzi and tony expected npv : There's a 50-50 chance of strong or weak lunch economy. Franzi's and Tony's Cost of Capital is 10%. What is Franzi's and Tony's expected NPV?
Determine the mass flow rate of dry air required : The heated air is then allowed to pass over the materials being dried, exiting the dryer at 150°F, 1 atm, and 30% relative humidity. If moisture is to be removed from the materials at a rate of 2700 lb/h, determine the mass flow rate of dry air re..
Why is this relevant and what is the role of leadership : Why is this relevant and what is the role of leadership?
Is every function a relation : What is the difference between an equation that is a function and one that is not - Is every function a relation? Is every relation a function?
Determine the temperature of the exiting moist air stream : Saturated water vapor at 230°F is sprayed into the moist air, which then exits the device at a relative humidity of 50%. Heat transfer between the device and its surroundings can be ignored, as can kinetic and potential energy effects. Determine t..
Construct a dot plot to represent the data : Construct a dot plot to represent the data. Use the number line provided - The table shows the number of hours worked per server.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd