Determine the manometer reading h for the manometer

Assignment Help Mechanical Engineering
Reference no: EM13626872

Air is drawn into a small open-circuit wing tunnel as shown. Atmospheric pressure is 98.7 kPa (abs) and the temperature is 45 degrees Celsius. If viscous effects are negligible, determine the pressure at the stagnation point on the nose of the airplane. Also determine the manometer reading, h, for the manometer attached to the static pressure tap within the test section of the wind tunnel if the air velocity within the test section is 60 m/s.

Reference no: EM13626872

Questions Cloud

A study was conducted to measure the effectiveness of a : a study was conducted to measure the effectiveness of a hypnotism in reducing pain. the measurements are centimeters on
For the vapor power cycle steam enters the at 3 mpa and 500 : for the vapor power cycle steam enters the at 3 mpa and 500 c and leaves at 70 kpa and 200 c. the system is operating
The plates of a parallel-plate capacitor are 328mm apart : the plates of a parallel-plate capacitor are 3.28mm apart and each has an area of 12.2 cm2. each plate carries a charge
Taking the object and liquid as a system how much word the : a 4 kg object traveling at 60 ms enters an insulated vat of 20 kg of incompressible fluid c 2.0 kjkgk and comes to
Determine the manometer reading h for the manometer : air is drawn into a small open-circuit wing tunnel as shown. atmospheric pressure is 98.7 kpa abs and the temperature
Methane oxygen and nitrogen flow into an insulated tank the : methane oxygen and nitrogen flow into an insulated tank. the methane flow is 2 kgs at the 320k. the oxygen flow is 3
Use the power series method to solve the radial equation : the schrodinger equation of a two dimensional harmonic oscillator potential can be handled by separation of variables
A venture necked-down section in a pipe develops a low : a venture necked-down section in a pipe develops a low pressure that can aspire fluid upward from a reservoir. derive
How long after the big bang did it take the universe to : how long after the big bang did it take the universe to cool to the threshold temperature for the formation of muons?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum speed

A vehicle of mass 1500kg and track 1.8m has a centre of mass located centrally at 1,1m above the ground. It has to travel around a bend of 56m radius to the centre of mass.

  On the same graph plot the copper temperature history

a copper sheet of thickness 2l2mm has an initial temperature of ti118c. it is suddenly quenched in liquid water

  Compute the second specimen radius after deformation

compute the second specimen's radius after deformation.

  A communication satellite weighing 10000 lb including fuel

a communication satellite weighing 10000 lb including fuel has been ejected from a space shuttle describing a low

  What is the velocity and rate of flow of the metal

What is the velocity and rate of flow of the metal into the mold? Is the flow turbulent or laminar? (Pure aluminum density ρ = 2.7 g/cm3).

  Find the tangential component of the acceleration when the

a partivcle along a plane cirve from point a to a point b. the path length between a and b is 60 in. the speed at a is

  A light pressure vessel is made of 2024-t3 aluminum alloy

a light pressure vessel is made of 2024-t3 aluminum alloy tubing with suitable end closures. this cylinder has a 3.50

  Use psychrometric chart to determine latent portion

Use Psychrometric chart to determine Latent portion

  A working fluid at 500kpa 400c 67315k is in a

a working fluid at 500kpa 400c 673.15k is in a piston-cylinder equipment with an initial volume of 0.9 m3. the fluid

  The mass of the piston is such that a cylinder pressure of

10 kg of water in a piston-cylinder arrangement exists as saturated liquidvapor at 100 kpa with a quality of 50. it is

  Find the distance a traveled by the piston if w is the work

a cylinder of cross-sectional area a is divided inot tow chambers 1 and 2 by means of a frictionless piston. the piston

  What compressive stress is required at zero strain if the

the imperial ore facility was operated by the galactic empire on the planet raxus prime. the refined ore produced

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd