Determine the magnitude and location of the maximum bending

Assignment Help Civil Engineering
Reference no: EM13542373

1.A 350 +sl m long graded bund is to be designed for a cultivated land with sandy loam soil and a surface slope of 4%. The bund channel is to be formed by the embankment only. The horizontal distance between two bund s is 50 m. The 1-hr rainfall expected during the recurrence interval of 10 yrs is 8 cm/hr.

2.For the beam and loading shown, write the equation of he shear and bending-moment curves and determine the magnitude and location of the maximum bending moment

3.When the driver applies the brakes of a light truck traveling 10 km/h, it skids 3 m before stopping. How far will the truck skid if it is traveling 80 km/h when the brakes are applied?

4.A beam of w16 X 50 section has a simple span of 20 ft. The beam is subjected to a uniform load of 2 kips/ft and an axial tensile force of 10 kips. Determine the maximum tensile and compressive stresses in the beam

Reference no: EM13542373

Questions Cloud

What is the total power into-out of the solenoid : A very long solenoid of radius a and height h has N closely wound turns of coil. Suppose there is an increasing current I(t) that runs through the coils. Consider a point P inside the solenoid (i.e. at r
A magician pulls a tablecloth from under : A magician pulls a tablecloth from under a 200 g mug located 30.0 cm from the edge of the cloth. The cloth exerts a friction force of 0.140 N on the mug, and the cloth is pulled with a constant acceleration of 2.90 m/s2. How far does the mug move rel..
Air which may be treated as an ideal gas : Air which may be treated as an ideal gas, is compressed from 100 kpa to 1500 kpa in a quasisatatic manner so that it obeys the relation ....pV^1.3 = constant determine the amount of work necessary to compress 100kg of air. The initial temperature ..
Determine vb of the load b after it has dropped 200 mm : A 40 kg sheave a OF RADIUS R=350 mm. and cenral radiusof gyration k=250 mm carries a 160 kg load b and is suspended by a cable and a spring of modulus k=1.2 kN/m. if the system is relased from rest in the positon show the spring is stretched 100 mm d..
Determine the magnitude and location of the maximum bending : For the beam and loading shown, write the equation of he shear and bending-moment curves and determine the magnitude and location of the maximum bending moment
Distance from the roadway to the floor of the vehicle : You are in charge of evaluating the safety (hazard) of a low water crossing. Traffic surveys show that the "Aaverage"vehicle using the crossing is semi-rectangular in shape (10 ft long, 5 ft wide, and 4.0 ft high - not including the distance from the..
Determine the most economical design pipe size and number : Determine the most economical design (i.e. pipe size and number and location of pumps). Hint: Vary your pipe diameter and consider pumps in series.
Determine the velocity of the collar at point b for values : To imagine the diagram, the collar at point A (unstretched) is on the same x-axis as the anchor @ C, while the collar point B (stretched) is located downwards-left to point A, forming a 30 degree angle with the y-axis (vertical). In other words, the ..
Assigning the central pier and the abutment as fixed : Design a 300 + sl m long variable graded terrace for a land having an average slope of 2 %. Maximum permissible velocity of water in the terrace channel is 60 cm/sec. The most sever rainfall expected in 10 yr RI has an intensity of 9 cm/hr.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Balancing of reciprocating engines

If the engine is mounted solidly on a rigid foundation, what is the alternating force amplitude transmitted? Assume the connection rod to be of infinite length.

  Type of reaction involving protonated alcohol

The reaction between 2-methyl-2-pentanol and HBr to yield 2-methyl-2-pentene is probably: A) an E1-type reaction involving the protonated alcohol as the substrate. B) an SN2-type reaction involving the protonated alcohol as the substrate.

  Suggest hen managentment strategy that will maximize profit

Each week a hen can either lay 12 eggs or hatch 4 eggs, but not both. At the end of the four-week period all eggs and chicks will be sold: an egg will bring 10 cents, and a chick will bring 60 cents.

  Calculate specific surface

Immediately after the bouncing golf ball leaves the floor itscomponent of velocity are Vx= 0.662 m/s and Vy= 3.66 m/s. determinethe horizontal distance from the point where the bal

  Determine the force that should be developed in the cable

Determine the force that should be developed in the cable if the saddle keeps the pipe from sagging or deflection at its center. The pipe and fluid within it have a combined weight of 125lb/ft. EI is constant.

  Find how much would the pressure in the tank increase

A rigid tank contains 5kg of water at 20 degrees Celsius. A gage on the tank reads 200kPa. Determine a) the volume of the tank, b) How much would the pressure in the tank increase if the temperature were increased to 50 degrees Celsius.

  Compute true percent relative error for each approximation

use zero through forth order taylor series expansions to predict f(2.5) for f(x) = ln x using a base point at x=1. compute the true percent relative error for each approximation. discuss the meaning of the results.

  The maximum population

The maximum population that can be served from the new development without exceeding the capacity of the trunk sewer. Diameter, slope, and invert elevations of sewer XB.

  Determine the resulting velocity of center of the cylinder

a 9in radius cylinder of weight 18lb rests on a 6lb carriage. the system is at rest when a force p of magnitude 2.5 lb is applied ( p is coming out of the car the cylinder is sitting on and going to the right) for 1.2s.

  Compute the after-tax rate of return on the vessel

At the end of the 6 years, the oil company exercised its option and bought the vessel. The chemical company has a 34% incremental tax rate. Compute its after-tax rate of return on the vessel.

  What is the minimum bottom width to effect the depth

A trapezoidal channel is to be designed to carry a discharge of 250 cfs at a normal depth of 3.5 ft. The channel is running on a slope of 0.005 ft/ft and the side slopes can be no steeper than 2.5 H on 1 V.

  What is the force between the bar and block d

Block D sits freely on the homogeneous bar and experiences a gravitational force of 50N. Homogeneous bar AB experiences a gravitational force of 25 N. What is the force between the bar and block D?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd