Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Repeat Problems 12.5 and 12.6 using a door weight of 250 N with the center of gravity 600 mm from the hinge. Spring torque for the door-open position as given in Problem 12.5 is to be 8 N m; net torque for the door-open position as given in Problem 12.6 is to be 16 N # m. The maximum allowable torsional stress is 350 MPa.
Problems 12.6
Suppose that the trap door in Problem 12.5 must be designed to open only 60° because there are clearance problems. Determine the length and diameter of torsion bar that would counterbalance 80 percent of the door weight when closed, and provide a net torque of 12 lb ft to hold the door against the 60° stop when open. Make a graph showing gravity torque, spring torque, and net torque all plotted against the door-open angle.
Problem 12.5
Figure P12.5 shows a fully opened trap door covering a stairwell. The door weighs 60 lb, with center of gravity 2 ft from the hinge. A torsion bar spring, extending along the hinge axis, serves as a counterbalance. Determine the length and diameter of a solid steel torsion bar that would counterbalance 80 percent of the door weight when closed, and provide a 6-lb ft torque holding the door against the stop shown. Use a maximum allowable torsional stress of 50 ksi. Make a graph showing gravity torque, spring torque, and net torque all plotted against the door open angle.
A 3 in. diameter low strength, stainless steel cylindrical part is to be turned on a lathe at six hundred rpm. With a depth of cut of .3 inches and a feed of .025 in/rev. what should be the minimum horsepower of the lathe?
a 75-g ball is projected from a height of 1.6m with a horizontal velocity of 2ms and bounces from a 400g smooth plate
You have a large hydraulic cylinder with a piston diameter of 8.00 inches. The rod of the cylinder is extended 48 inches. The pressure inside the cylinder at time, t = 0.00 sec is 1,000 psig. There is a 10 foot long hose connected to the hydraulic cy..
the 30 mg aircraft is climbing at the angle theta15 with a thrust t of 180 kn. at the instant shown its speed is 300
Consider an extended surface of rectangular cross section with heat flow in the longitudinal direction. W/m2 · K. What is the temperature of the rod 25, 50, and 100 mm from the casting?
determine the equilibrium temperature of ceramic plate 300mm long 150 mm wide and 20 mm thick when it is normal to the
1. Determine the volume change, in ft3, when 1 lb of water, initially saturated liquid, is heated to saturated vapor while pressure remains constant at 1.0, 14.7, 100, and 500, each in lbf/in.2 Comment. 2. For H2O, determine the specified property..
Design a short square tied column to carry a factored axial design load Pu of 890 kips and a factored design moment Mu of 390 ft.-kips. Place the longitudinal reinforcing uniformly in the four faces.
A) A huge reservoir of air supplies a converging-diverging nozzle with throat and exit areas of 10 cm^2 and 25 cm^2 respectively. The reservoir pressure and temperature are 150 kPa and 20C. Determine the range of back pressure over which
water vapor exists at a pressure of 10kpa and temperature of 373k. assume a reference atmosphere exists at to 298k and
how is diffusion time related to diffusion temperature for the case where the concentration at some distance into an
Draw the shear and moment diagrams for members AB and AF. Sketch the deflected shape, and determine the deflection at midspan
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd