Determine the laplace transform ys of the step response

Assignment Help Electrical Engineering
Reference no: EM13270240

consider a continuos LTI system with step response given by ys(t) = tu(t) - (t - 2)u(t - 2). A. Determine the laplace transform X(s) of the input signal x(t) = u(t). B. Determine the Laplace transform Ys(s) of the step response. C. Determine the transfer function H(s) for the system. D. Determine the impulse response h(t) for this system using complex domain (not time domain) analysis techniques.

Reference no: EM13270240

Questions Cloud

State a solution of salicylate dianion is prepared by mixing : A solution of salicylate dianion is prepared by mixing 0.158 g of reagent grade acetylsalicylic acid in 5 mL of 1 M sodium hydroxide and heating the mixture until all of the solid dissolves.
What was the mass of the ice cube : A cube of ice is taken from the freezer at -9.5?Cand placed in a 95-g aluminum calorimeter filled with 310g of water at room temperature of20.0 ?C. What was the mass of the ice cube
What is the future value of the same annuity due : If the future value of an ordinary, 8 year annuity is $5,800 and interest rates are 8.0 percent, what is the future value of the same annuity due?
Calculate the energy absorbed from a climbers body : High-altitude mountain climbers do not eat snow, but always melt it first with a stove. Calculate the energy absorbed from a climber's body if he eats 0.70kg of -15?C snow which his body warms to body temperature of 37?C
Determine the laplace transform ys of the step response : consider a continuos LTI system with step response given by ys(t) = tu(t) - (t - 2)u(t - 2). A. Determine the laplace transform X(s) of the input signal x(t) = u(t). B. Determine the Laplace transform Ys(s) of the step response.
Explain oxygen to allow complete combustion : containing too little oxygen to allow complete combustion of the fuel is called a rich mixture. A high-performance heater that burns propane, C3H8(g), is adjusted so that 100.0 g of O2(g) enters the system for every 100.0 g of propane. Is this mix..
Find the value of r that would provide critical damping : An RLC circuit exists, with current flowing counter clockwise through it. R= 5.661 Ohms, L=20.2 mH, and C=157.6?F. Voltage across the capacitor is positioned so that the current meets the positive terminal first.
What wavelength photon is given off : Consider a fluorescent molecule where the electron that participates in fluorescence has ground state energy of -4.6 eV. what wavelength photon is given off
What is the net advantage to leasing : Green Valley Farms uses straight-line depreciation, has a 32 percent tax rate, borrows money at 8 percent, and has sufficient tax loss carryovers to offset any potential taxable income the firm might have over the next five years. What is the net ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine of power density that is reflected from interface

A 100 MHz plane wave is incident from air onto a dielectric medium ( \(\epsilon=\epsilon _{o}\) ) at normal incidence. Find the below. a. \(\Gamma \) and SWR b. \(\lambda \) in air and in dielectric c. Percentage of power density that is reflected f..

  What is corresponding gate length for mos transistors

What is the (approximate) maximum electric field intensity for which constant mobility may be assumed for electrons in silicon. In a digital circuit with a supply voltage of 1V, what is the corresponding gate length for MOS transistors.

  Calculate speed if load torque is reduced to three times

The DC shunt motor is running at full load with a supply voltage of 440 V and a supply current of 70 A. The rotation speed in full load is 1000 rpm, the field resistance is 200 Ohm and the armature resistance is 0.2 Ohm.

  Find the equivalent impedance for z1

Find the equivalent impedance for Z1 = 60 L+60 and Z2 = 80 L-45 when these are connected in parallel What are the branch currents and the total circuit current if the supply voltage to the circuit is VS = 240V L0

  How to combine the expressions into a single sinusoid

How to Combine the following expressions into a single sinusoid and plot both the combined and original expressions in Matlab across 2 periods. a) 2cos(3t)-cos(3t-pi/4) b) sin(2t- pi/4) + 2cos(2t-pi/3) c) cos(t) - sin(t) d) 10cos((pi*t) + pi/3) + ..

  What will be the step-angle for a hybrid stepper motor

If a stepper motor has a step-angle of 7.5? , what digital input rate is required to produce a rotation of 10 rev/sec What will be the step-angle for a hybrid stepper motor with eight stator windings and ten rotor teeth

  What is the all day efficiency of the transformer

A 25KVA transformer supplies a load with the following schedule: 8hrs-full load with 0.8 lagging power factor. 4hrs-75% full load at unity power factor. 12hrs-No load. The transformer is energised 24hrs per day and has iron losses of350w.

  What is the maximum power transfer that can be achieved

The power transfer in a transmission line is governed by the equation P = VS * VR * sin\(\delta\)/X line. Basedon this equation what is the maximum power transfer that can be achieved, and what is its value if VS =VR = 1.0p.u

  What will be the output voltage from the bridge for a change

What will be the output voltage from the bridge for a change in temperature of 20o C The supply voltage to the bridge is 6.0 V and the temperature coefficient of resistance of the platinum is 0.0039 K-1.

  What is the magnetic energy per unit of wire lenght

In a long cilindric wire with a radius of 2 cm, a corrent with 80A goes thorugh it. What is the magnetic energy per unit of wire lenght?

  What is the received bit pattern corresponding to part a

b) Draw the LFSR circuit to generate the CRC. Generate the CRC by applying the data pattern to the LFSR and verify the answer in part a. c) An error vector is given by X7+ X6+ X4+ X3+1. What is the received bit pattern corresponding to part a

  Design class-a transformr-coupled emitter-follower amplifier

Design a class - A transformer-coupled emitter-follower amplifier to deliver 10 W to an 8 Ohm speaker. The ambient temp is 25 C and the maximum junction temp is Tj max = 150 C. assume the thermal resistance value are dev-case = 3.2 C/W

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd