User Account

All Pages

Determine the inner diameter of the bones cross section at

Assignment Help Mechanical Engineering
Reference no: EM13623837

A Stress gauge located at C on the surface of the bone AB indicates that the average normal stress in the bone is 3.80 MPa when the bone is subjected to two 1200N forces as shown. Assuming the cross section of the bone at c to be annular (two concentric circles) and knowing that its outer diameter is 25 mm. Determine the inner diameter of the bones cross section at C. (The 2 1200N forces are pullling the bone apart at ends A and B, with the gauge at C in the middle of the length of the bone)

Reference no: EM13623837

Questions Cloud

Janicex co is growing quickly dividends are expected to : janicex co. is growing quickly. dividends are expected to grow at a rate of 20 percent for the next three years with
A 10-m-by-14-m house is built on a 12-cm-thick slab of : a 10-m-by-14-m house is built on a 12-cm-thick slab of concrete. what is the rate of heat loss through the slab if the
311 x 1016 electrons are passing from left to right through : 3.11 x 1016 electrons are passing from left to right through a wire every seconds. what is the current in that wire in
Water at 400kpa with a quality of 25 has its temperature : water at 400kpa with a quality of 25 has its temperature raised 20c in a constant-pressure process. what is the new
Determine the inner diameter of the bones cross section at : a stress gauge located at c on the surface of the bone ab indicates that the average normal stress in the bone is 3.80
The surface absorbs half of the energy and reflects half : a plane electromagnetic wave has an energy flux of 711 wm2. a flat rectangular surface of dimensions 100 cm times 24 cm
The computer chips in notebook and laptop computers are : the computer chips in notebook and laptop computers are produced from semiconductor wafers. certain semiconductor
Henry garrison starts the month with a balance on his : henry garrison starts the month with a balance on his credit card of 1130. the average daily balance for the month
Assume frictionless surfaces and let g981 ms2 determine the : a block of mass 10kg moves along a surface inclined 30acircdeg relative to the horizontal. the center of gravity of the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the temperature cm from the base

What is the temperature 7 cm from the base if the rod is made of a) pure zinc b) lead c) pure gold. Which will be the hottest at this point?

  Calculate the work in kjkg done per unit mass of the steam

steam at 2.5 mpa and 400 c enters an adiabatic steam turbine with a low velocity and leaves with a velocity of 180 ms

  Calculate the local atmospheric pressure in the city in kpa

1. write out the differences betweena close system and open systemgive one example and state what type of system it isb

  Calculate the force necessary to cause

A cylindrical specimen of this alloy 24 mm in diameter and 186 mm long is to be pulled in tension. Calculate the force necessary to cause a 0.0119 mm reduction in diameter. Assume a value of 0.33 for Poisson's ratio.

  The temperature of the steam entering the turbine is 700 f

a rankine cycle operates between pressure limits of 500 and 2 psia. the temperature of the steam entering the turbine

  Heat transfer occurs at a rate of 2 kw from the compressor

air enters a compersoor operating at steady state at 1.05 bar 300k with a volumetric flow rate of 12 m3min and exits at

  Knowing that x 5 0 at t 5 0 determine a the distance the

based on observations the speed of a jogger can be approximated problems 617 by the relation v 5 7.51 2 0.04x0.3 where

  What is the maximum efficiency of the heat engine

What is the work you get out of each kJ of heat extracted from the basin? Repeat for the case that the water is at 100C. Comment on why efficient car engines run so hot.

  A city water main to the water tower and is 794 feet above

based solely on static elevation head if the water level in a city water tower is 860 feet above sea level and the

  Determine the force of the rod on the particle and the

the particle has a mass of 0.5 kg and is confined to move along the smooth horizontal slot due to the rotation of the

  A food liquid with a viscosity of 00209 lbf-sft2 is being

a food liquid with a viscosity of 0.0209 lbf-sft2 is being pumped through a two-inch stainless steel pipe at a rate of

  What is the k.e. of the satellite

A satellite has been placed in a circular, sun-synchronous orbit at an altitude of 1300.0 km. The satellite has a mass of 5,000.0 kg. What is the K.E. of the satellite?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd