Determine the indicated property

Assignment Help Mechanical Engineering
Reference no: EM13717474

Using the appropriate table, determine the indicated property. In each case, locate the state on sketches of the T-v and T-s diagrams. Include the vapor dome on the diagram.

a) Water at p = 0.20 bar, s = 4.3703 kJ/kg.K. Find h, in kJ/kg.

b) Water at p = 10 bar, u = 3124.4 kJ/kg. Find s, in kJ/kg.K.

c) Refrigerant 134a at T = -28oC, x = 0.8. Find s, in kJ/kg.K.

d) Ammonia at T = 20oC, s = 5.0849 kJ/kg.K. Find u, in kJ/kg.

Please explain which table you use, and any calculations (if needed) to find the values on the table.

Reference no: EM13717474

Questions Cloud

Bank account at the end of every month : Bill plans to deposit 200 into bank account at the end of every month. The bank account have the nominal interest rate of 8% and interest is compounded monthly. How much will bill have in the account at the end of 21/2 years ( 30month)
Find the current in the other wire : Two parallel wires separated by 4.2 cm repel each other with a force per unit length of 1.9 x 10-4 Nm. The current in one wire is 4.9 A. Find the current in the other wire
Evaluate what is the temperature coefficient of resistivity : A wire 3.00 m long and 0.450 mm2 in cross-sectional area have a resistance of 39 at 20°C. If its resistance increases to 39.7 Ω at 26.0°C, What is the temperature coefficient of resistivity
What is the escape velocity of the planet : A huge cannon is assembled on an airless planet. The planet has a radius 5.00 x 106m and a mass of 4.6 x1024 kg. The cannon fires a projectile up at 4000 m/s. what is the escape velocity of the planet
Determine the indicated property : Using the appropriate table, determine the indicated property. In each case, locate the state on sketches of the T-v and T-s diagrams. Include the vapor dome on the diagram.
Find the average power of the elevator motor : A 636-kg elevator starts from rest and moves upward for 2.60 s with constant acceleration until it reaches its cruising speed, 1.75 m/s. What is the average power of the elevator motor
Paraphrasing of other material must be footnoted : Need a paper an original paper on Shot-Sellling. Papers should be 12 pages double spaced, and 15 should be considered a reasonable maximum. Papers MUST include a bibliography of sources cited. Any direct or indirect quoting or paraphrasing of ..
Calculate the average heat transfer coefficient over : Atmospheric air at T = 40°C with a free stream velocity u = 8 m/s flows along a flat plate L = 3 m long which is maintained at a uniform temperature of 100°C. Calculate the average heat transfer coefficient over t
What is the new voltage across the plates : A dielectric of k=3 is inserted between two charged parallel plates, completely filling the 2cm space between them. what is the new voltage across the plates

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd