Determine the horizontal distance at the instrument

Assignment Help Civil Engineering
Reference no: EM13326196

Stadia is used to estimate the distance from the instrument to a target. Using inclined sights the horizontal distance and vertical distance between the center of the instrument and the target and the elevation of the rod can be determined.

1) determine the horizontal distance, given:Stadia Top=8.5 ,Stadia Bottom 6.21, vertical angle= -8 degrees 42 minutes.

2)If the ground elevation at the instrument is 2045' msl (mean sea level), what is the ground elevation at the rod?

Reference no: EM13326196

Questions Cloud

What will be changes in discharge of the stream : If the stage of a stream increases by 40% and the slope of the water surface becomes half of its original slope, then what will be changes in discharge of the stream
How much sideways force must the tires exert : A higway curve with a radius of 400m is banked properly for a car traveling 120km/h. how much sideways force must the tires exert
Find the deflection as the person walks across the rope : The distance between the poles holding the rope is 90 ft. We are to find the tensions in both sides of the rope for someone walking across the rope and the deflection for every 0.5 ft up to 45 ft.
Design an improved interactive password system : Design an improved interactive password system? Present your design and describe what kind of attacks your protocol can protect.
Determine the horizontal distance at the instrument : Stadia is used to estimate the distance from the instrument to a target. Using inclined sights the horizontal distance and vertical distance between the center of the instrument and the target
Find the magnitude of the resulting acceleration : The magnitude of each force is 271 N, the force on the right is applied at an angle 20? and the mass of the block is 13 kg. what is the magnitude of the resulting acceleration
What is the role of technology in effective gvts : what is conflict? is all conflict the same? does conflict occur within GVTs? what causes it? how can conflict be managed within GVTs?
Tensile stress and compressive stress : How the tensile stress and compressive stress result in the moment about neutral axis when the beam fails
Find an expression for the moment of inertia : The Earth has mass ME and average radius RE. Find an expression for the moment of inertia IE of the Earth on its axis in terms of the given parameters

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the deflection in degree for horizontal wind speed

Determine the deflection in degrees for horizontal wind speed of 10m/s and what is the magnitude of the force required at the bottom of the sign to prevent the sign from deflecting

  Determine station of pvc and pvt and design speed of curve

An equal-tangent crest vertical curve connects a +3.2% and -1.1% grade. The PVI is at station 98+20. Due to drainage considerations, the highest point of the curve is at station 100+79.35.

  Calculate the coefficient of volume compressibility

In an oedometer test, the void ratio of a clay sample changed from 1.62 to 1.41 as the vertical effective stress imposed on the sample was increased from 100 kPa to 200 kPa.

  Falling-head permeability test

A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm.

  Determine what is runoff coefficient in a basin located

What is the runoff coefficient in a basin located near the middle of the climatic spectrum, with annual precipitation P = 32 in, ecosystem evapotranspiration ET = 22 in, and baseflow U = 3 in

  Determine the maximum shearing stress in each shaft

Knowing that G = 11.2 x10^6 psi, determine the maximum shearing stress in each shaft when a torque of T of magnitude 420kip*ft is applied to the flange indicated. And the torque T is applied to flange B.

  Calculate 5 day cbod of the river after mixing with waste

An industry discharges .5m^3/s of waste with a 5 day CBOD of 500 mg/l to a river with a flow of 2 m^3/s and a 5 day CBOD of 2 mg/l calculate the 5 day CBOD of the river after mixing with the waste.

  Determine the location where a hydraulic jump forms in flat

A rectangular open channel with a width of 10 ft and n = 0.013 conveys a discharge of 300 cfs. The upstream portion of the channel has a slope of 10%, which then abruptly changes to a slope of zero downstream.

  Determine vertical stress increment due to the strip load

Soil with a unit weight of 19.65 kN/m^3 is loaded on the ground surface by a strip load of 1.5 m wide. The strip load is 365 kN/m of wall length. Determine the vertical stress increment due to the strip load and the total pressure

  Determine reaction components that ball exert on rod abc

The smooth surface that provides the support at C lies in the y-z plane. Determine the reaction components that the ball and socket exert on rod ABC, the tension in cable BD, and force the smooth wall exerts on end C of rod ABC.

  What is the discharge through the pipe for water temperature

A fire hydrant is supplied through a 6 inch cast iron pipe of 16,000 feet length. The total drop in pressure is limited to 35 psi. What is the discharge through the pipe for a water temperature of 80°F ((kinematic viscosity) = 0.93 × 10-5 ft2/sec)

  How many iron atoms are contained in the paper clip

A typical paper clip weighs 0.59 gram and consists of BCC Iron. The density of iron is 7.87 gram/cm3 and its atomic radius is 0.124 nm. What is the volume of a unit cell in (nm)3. What is the volume of a unit cell in cm3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd