User Account

All Pages

Determine the horizontal and vertical forces

Assignment Help Civil Engineering
Reference no: EM132637164

The 1-m wide gate ab depicted on the right retains water 6 m deep. Determine the horizontal and vertical forces on the gate, and then calculate magnitude and direction of the resultant force on the gate.

Reference no: EM132637164

Questions Cloud

Determine all the elements of the reversed curve : Determine all the elements of the reversed curve including the stations. Use arc basis.
Discovered several methods to attack-defeat cryptosystems : Malicious individuals have discovered several methods to attack and defeat cryptosystems.
Water surface profile by numerical integration : Compute the water surface profile by the numerical integration method to a depth 5% greater than the uniform flow depth. a = 1.1 and n = 0.025.
Post the October transactions to the general journal : Earned but unbilled fees at October 31 were $2,500 and Depreciation for the month was $500. Post the October transactions to the general journal
Determine the horizontal and vertical forces : Determine the horizontal and vertical forces on the gate, and then calculate magnitude and direction of the resultant force on the gate.
Challenges of big data analytics : There are several benefits as well as challenges associated with the use of Big Data Analytics in the e-Healthcare industry.
Should company accept or reject the order and explain why : Should the company accept / reject the order and explain why? Variable (material labor and overhead) 40 per unit. Fixed overhead 30,000
How will change negatively impact its business reporting : You are tasked with creating a document for the owner that addresses the following: How will change negatively impact its business reporting
What are the environmental factors on moon : What conditions does life need? Life exists on earth so what environmental factors does the earth have to provide the conditions for life?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the firssorder decay rate constant

If the desired chlorine residual in the treater water after it leaves the reactor is 0.20 mg L-1 . and the chlorine demand used during treatment is 0.15 mg L-1 , what must be the daily mass of chlorine added to the reactor in grams?

  What would be failure deviatoric stress sigma1-sigma3 stress

The effective angle of friction (phi) was found to be 26 degrees for a normally consolidated soil. If the soil is tested in consolidated drained triaxial test under sigma3 = 60 kPa, what would be the failure deviatoric stress sigma1-sigma3 stress

  Under what circumstances is there an exception to law

under what circumstances is there an exception to the general law that an identified original section corner controls the positions of the boundary lines meeting at or passing through the corner

  Calculate the fluid viscosity if the torque on the inner

For two 0.2 m long rotating concentric cylinders, the velocity distribution is given by u(r) = 0.4/r - 1000r m/s. If the diameters are 2 cm and 4 cm, respectively, calculate the fluid viscosity if the torque on the inner cylinder is measured to be 0...

  Unit 18 Civil Engineering Technology Assignment

Unit 18 Civil Engineering Technology Assignment Help and Solution, Higher National Certificate/Diploma in Construction and the Built Environment Assessment

  Determine the work done by the air

Determine the work done by the air and the total heat transferred to the air during this process. Also show the process on a P-v diagram.

  How to assume a weight od 150 pcf for reinforced concrete

it carries a uniform service load of 2450 lb/ft in addition to its own weight. material strengths are f'c=4000psi and fy=60000psi .assume a weight od 150 pcf for reinforced concrete.

  Calculate the ideal effort force needed to overcome force

Place the scientific mass on the inclined plane and string over the pulley. Using a force-measuring device, pull the string and determine the force needed to obtain static equilibrium.

  Calculate the work necessary to compress air in cylinder

Calculate the work necessary to compress air in an isolated cylinder from a volume of 6 ft^3 to a volume of 1.2 ft^3. The initial pressure and temperature are 30.0 psia and 50 degree F, respectively.

  What is actually measured at the rec5

There are two methods for determining the range from the SV to the REC in GPS. Code (C/A and P) and waves (L1 and L2) discuss two elements of GPS signals as they relate to each method. choose from the list of elements shown below.1.determination of t..

  Does this law hold exactly for ideal-gas mixtures

Does this law hold exactly for ideal-gas mixtures? How about nonidealgas mixtures?

  Determine the rate of heat transfer from the balls to air

Assuming 85 percent of the heat generated in the resistance wires is transferred to the plate, determine the minimum time needed for the plate temperature to reach 140°C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd