Determine the height of the wake region h

Assignment Help Civil Engineering
Reference no: EM13210747

A rudder is tested in a two-dimensional flow tunnel of height h = 1 m, as shown in the following figure. After the flow has become steady, the horizontal velocity far ahead of the rudder is found to be uniform and given by u = U = 2 m/s. Some distance downstream, the velocity profile can be (very) roughly approximated by a region inside the wake with u = U/2 and an exterior region with u = 3U/2. You may assume that the total pressure at the downstream station is uniform across the tunnel and given by the value at the wall. Neglecting gravitational effects:

a. Determine the height of the wake region H.
b. Assuming ideal fluid flow (no shear stress), calculate the difference in pressure at point A and point B (i.e. pA - pB).
c. Calculate the drag force on the body.

 

Reference no: EM13210747

Questions Cloud

Determine the cycle time for a single engine scraper : Determine the cycle time for a single engine scraper rated at 21 cy heaped that is used to haul material from a pit to a fill 900 ft away under severe conditions.
Which company presents the most risk for the investors : Is it possible to have a portfolio of two securities whose s is less than the s of either of the two securities? Can you show an example to justify your position?
Explain the necessity of super elevation in the design : explain the necessity of super elevation in the design of horizontal curve also prove that rv=v2/{g(fs+e)}
Depict the enediol that is believed to be the intermediate : A certain aldose is added to an aqueous sodium hydroxide solution. After equilibrium is reached it is found that there are 3 open chain sugars in the solution. Draw the enediol that is believed to be the intermediate.
Determine the height of the wake region h : You may assume that the total pressure at the downstream station is uniform across the tunnel and given by the value at the wall. Neglecting gravitational effects.
Disparate impact and desparate treatment theories : Describe the procedures required to file a discrimination lawsuit under the disparate impact and desparate treatment theories. How is adverse impact determined? Provide a scenario illustrtaing evidence of adverse imapct in an employmnet decisison?
Determine the coefficient of friction : a mass of 2kilogram is projected with a speed of 3m/s.if a plane inclined 20 degrees with the horizontal.after travelling travelling 0.8meters, the mass comes to rest. determine the coefficient of friction and also the speed as the black returns t..
Find out the molar enthalpy or heat of a reaction : -Determining the molar enthalpy/heat of a reaction, and then how much heat was actually given off in a specific reaction -Finding the increase in temperature of a substance given its gain or loss of heat energy
Mob violence against abolitionists-the mayflower compact : The immediate cause for the Texan Americans' declaration of independence on March 2, 1836 was that... The First Continental Congress... Mob violence against abolitionists...The Mayflower Compact...

Reviews

Write a Review

Civil Engineering Questions & Answers

  Percentage of kinetic energy

In what direction did the cue ball move after the collision? What percentage of its kinetic energy did the cue ball impart to the eight ball?

  Determine the compression of each spring

The 75 lb block is released from rest 5 ft above the plate. Determine the compression of each spring when the block momentarily comes to rest after striking the plate.

  Design a cantilever

Need to design a cantilever retaining wall 8m high, saturated unit weight is 16kn/m 3 , surcharge is 7kn/m 2 , load above wall supported on wall stem

  Define the grade of the highway

The grade of the highway, Suppose that a highway rises a distance of 269 feet in a horizontal distance of 2647 feet.

  Position of the race car when acceleration is given

Starting from x = 0 with no initial velocity, the acceleration of a race car is defined by the relation a = 6.8e- 0.00057x , where a and x are expressed in m/s 2 and meters, respectively. Determine the position of the race car when v = 30 m/s.

  Define base isolation technique has become the method

Base isolation technique has become the method of choice for structural design of buildings and bridges located in highly seismic areas in recent years.

  Calculate the total drilling cost

Calculate average figures for tonnes/round and powder factors in kg/tonne and Determine the drill metres required to achieve a production rate from grade control blasting.

  Maximum acceleration from rest

The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque. If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for:

  Net rate of flow of linear momentum via control surface

Measurements indicate that to cause this flow the force acting on the contents of the control volume is 40i lb. Determine the net rate of flow of linear momentum through the control surface.

  What is the total bod loading per day

The factory will use a 4 ft deep on-site lagoon to stabilize the waste with a loading rate of 20 lb BOD/acre-day. Part a) What is the total BOD loading per day?

  Define introduction to management science

Introduction to management science, The Dynaco Manufacturing Company produces a particular product in an assembly line operation. One of the machines on the line is a drill press that has a single assembly line feeding into it.

  Di-atomic ideal gas

Air can be assumed as a di-atomic ideal gas. Find the final temperature and the amount of work ( in kW) required for air compression at a rate of 100 mol/s , from an initial condition of 1 bar an 25 C to 10 bar; for the following ways:

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd