Determine the heat transferred to and rejected from this

Assignment Help Mechanical Engineering
Reference no: EM13641280

Someone has suggested that the air-standard Otto cycle is more accurate if the two isentropic processes are replaced with polytropic processes with a polytropic exponent n = 1.3. Consider such a cycle when the compression ratio is 8, P1 = 95 kPa, T1 = 15°C, and the maximum cycle temperature is 1200°C. Determine the heat transferred to and rejected from this cycle, as well as the cycle's thermal efficiency. Use constant specific heats at room temperature.

Reference no: EM13641280

Questions Cloud

Containers arrive at a stocking station on a conveyor at : containers arrive at a stocking station on a conveyor at the rate of five per minute. container weight is 25 kg.
Determine the power produced by this engine when it is : an ideal diesel cycle has a maximum cycle temperature of 2300degf and a cutoff ratio of 1.4. the slate of the air at
A system of two sources consist of a solid non-conducting : a system of two sources consist of a solid non-conducting sphere of radius r10cm with charge q uniformly distributed
A 500kg truck moving at 30 ms strikes a parked 300kg car : a 500kg truck moving at 30 ms strikes a parked 300kg car. they connect together and move forward.a what kind of
Determine the heat transferred to and rejected from this : someone has suggested that the air-standard otto cycle is more accurate if the two isentropic processes are replaced
How many grams of dipotassium oxalate mw16622 should be : how many grams of dipotassium oxalate m.w.166.22 should be added to 27.293 ml of 0.6682 m hclo4 to provide a solution
Calculate the top speed at sea level of the vehicle if the : the 2012 lamborghini muricielago has a 640 horsepower engine drag coefficient of .33 and a cross sectional area of 2.35
An electron moves at a speed of 600 ms directly toward a : an electron moves at a speed of 60.0 ms directly toward a stationary electron when the two electrons are 1.00 m apart.
1 what is the difference between the electric field : 1. what is the difference between the electric field electric potential and the force exerted by the electric field?2.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A hydraulic cylinder has a piston of cross sectional area

a hydraulic cylinder has a piston of cross sectional area 45cm2 and a constant working fluid pressure of 2.2mpa. the

  Estimate the temperature of the hottest point in the billet

Estimate the temperature of the hottest point in the billet after five minutes of quenching. Neglect end effects; make the calculation for a cylinder of the given diameter but of infinite length.

  A 15 kg block b is being pulled along a smooth surface by

a 15 kg block b is being pulled along a smooth surface by a winch a. assume the winch is a 10 kg disc with a constant

  A pipe at the focal line receives 450 lbmhr of water at 200

a 300-foot-long 6-ft-wide parabolic trough concentrator receives normal solar radiation at 905 wm2. a pipe at the focal

  The turbine to the surroundings is neglible as are kinetic

steam enters an extraction turbine in a vapor power plant operating at steady stte at 10 mpa 480 c. 25 of the steam is

  Air at 1 atm and 30 degc flows over a 15 cm square plate at

air at 1 atm and 30 degc flows over a 15 cm square plate at a velocity of 10 ms.a. calculate the maximum boundary layer

  Refrigerant 134a enters an adiabatic compressor as

refrigerant 134a enters an adiabatic compressor as saturated vapor at 200kpa at a rate of 30 kgmin and is composed to a

  If a light bulb bought from a particular store has a 18

if a light bulb bought from a particular store has a 1.8 probability of being defective when it leaves the store

  When subjected to the axial load p the diameter of the rod

a solid circular rod with a diameter of d 18mm. the bar is ade of an aluminum alloy that has an elastic modulus of e

  Determine the maximum speed

A vehicle of mass 1500kg and track 1.8m has a centre of mass located centrally at 1,1m above the ground. It has to travel around a bend of 56m radius to the centre of mass.

  Determine the ideal launch vehicle

Determine the ideal launch vehicle that can put this orbiter into the parking orbit. (hint: you do not have to consider the Sun in this problem. Only SOI of the Earth and the Moon)

  The wind tunnel model is 110 the size of the actual column

we want to model the force of river water o some bridge support columns with a scale model in a wind tunnel. the actual

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd