Determine the heat transfer for the process

Assignment Help Mechanical Engineering
Reference no: EM13711558

A closed system of mass 10 kg undergoes a process during which there is energy transfer by work from the system of 0.147 kJ/kg, an elevation decrease of 50 m, and an increase in velocity from 15 m/s to 30 m/s. The specific internal energy decreases by 5 kJ/kg. The acceleration of gravity is constant at 9.7 m/s2. Determine the heat transfer [kJ] for the process (magnitude and direction).

Reference no: EM13711558

Questions Cloud

Steady-state conditions with negligible inlet velocity : Air enters a well-insulated turbine operating at steady-state conditions with negligible inlet velocity, 4 MPa, and 100°C. The air expands to an exit pressure of 100 kPa. The exit velocity and temperature are 90 m/s and 100°C, respectively. The diame..
The ratio of mass flow rates of warm to cold air streams : In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The ra..
What is the volume occupied by each gas at equilibrium : An insulated rigid container is separated into two parts using a partition that is free to move and the partition allows heat transfer without any energy storage by itself. Initially 2 kg of air at 5 bar and 350 K is contained on one side of the part..
Gas is contained in a vertical piston-cylinder assembly : Gas is contained in a vertical piston-cylinder assembly. The initial volume of the gas is 0.1 m3 and the initial pressure is 500 kPa. The gas undergoes a quasi equilibrium expansion process to a final volume of 0.25 m3. For each case below, determine..
Determine the heat transfer for the process : A closed system of mass 10 kg undergoes a process during which there is energy transfer by work from the system of 0.147 kJ/kg, an elevation decrease of 50 m, and an increase in velocity from 15 m/s to 30 m/s. The specific internal energy decreases b..
The rate of heat transfer from the air to the walls is small : A 1.5 kilowatt heater is to be used to heat a room with dimensions 3.5 m × 5.0 m × 3.0 m. There are not heat losses from the room, but the room is not airtight, so that the pressure in the room is always atmospheric. Consider the air in the room to b..
Determine the specific internal energy at the final state : A vertical piston/cylinder device contains 0.01 lbm of gas. The initial gas volume is 0.18 ft3 and the initial specific internal energy is 282 Btu/lbm. The piston, with a mass of 110 lbm and cross-sectional area of 0.11 ft2, is in equilibrium with th..
Find the reservoir that the stream of water exiting nozzle : A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..
Determine the volume and height of the cooling tower : A counter flow cooling tower cools 2000 gal/min water from 104 F to 85 F with 210,000 ft^3/min of air at 90 F Dry bulb Temperature and 76 F WBT . The Mass transfer coefficient -surface area product is hA= 123lbm/hr ft^3. Air mass flow rate per unit c..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd