Determine the heat exchanger effectiveness

Assignment Help Civil Engineering
Reference no: EM132416616

The hot and cold inlet temperatures to a concentric tube heat exchanger are Th,i=160°C, Tc,i=100°C, respectively. The outlet temperatures are Th,o= 120°C and Tc,o= 135°C.

Determine the heat exchanger effectiveness?

Determine the NTU?

Reference no: EM132416616

Questions Cloud

Estimate the mttf and the standard deviation : Estimate the MTTF and the standard deviation of the failures times. Also conclude that the failure rate is decreasing, constant, or increasing
Hot water outlet temperature for counterflow operation : Determine the hot water outlet temperature for counterflow operation, in °C. Determine the hot water outlet temperature for parallel flow operation, in °C.
Plant mineral nutrition scientific report : Plant Mineral Nutrition Scientific Report Assignment Help and Solution - Prepare separate figures for shoot length, root length, leaf number, leaf area
What is the heat transfer rate : What is the heat transfer rate, in W? What is the water volumetric flow rate, in L/min? What is the capacity ratio?
Determine the heat exchanger effectiveness : Determine the heat exchanger effectiveness? Determine the NTU?
Estimate and plot the failure density : Estimate and plot the failure density, reliability, and hazard functions based on the failure data.
What is the real enthalpy of the discharge line : However, the compressor adiabatic efficiency is 70%, so what is the real enthalpy of the discharge line.
How the rates of incarceration vary by gender and race : Explain how the rates of incarceration vary by gender and race. Distinguish between prison, parole, probation, and jail systems and their growth since 1970.
What you read and know about your own community : You have been asked by your Chief to establish a list of leadership qualities to look for in a supervisor. What should your list contain and why?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the maximum shear stress in the magnesium

A hollow magnesium shaft is rigidly bonded to a solid steel shaft and rigidly mounted between two supports. A torque of 500 NA·m is applied at the junction between the two shafts. What is the maximum shear stress in the magnesium?

  What is the rated flywheel power for a cat 834h 4 wheel

What is the rated flywheel power for a CAT 834H 4 wheel tractor equiped with converter drive? What are the maximum speeds, for this machine in each of the four forward gears?

  Calculate the mass flux rate and the flow rate

Water is flowing in a 6-cm diameter pipe at 20 m/s at 10?C. If the pipe enlarges to a diameter of 12-cm, calculate the reduced velocity. Also, calculate the mass flux rate and the flow rate.

  List at least five types of potential losses

Liquidated damages are intended to represent anticipated losses to the owner based upon circumstances existing at the time the contract was made. List at least five types of potential losses to the owner that would qualify for determination of suc..

  Compute the circumferential stress to which the wall

The length of a reading room in a library is 10 m and its breadth is 8 m. Compute the distributed live load, assuming the basic value of the load to be 2873 N/m2.

  Determine the volume of irrigation water needed in ac-ft

A certain crop has a consumptive use requirement of 1.2 ac-ft of water per acre of crop land. The crop is planted on 780 acres of land. Precipitation falling during the growing season is 3.2 inches.

  What is min coefficient of road adhesion needed to achieve

The owners wish to achieve an initial acceleration from rest of 22 ft/(sec^2) on a level paved surface. What is the minimum coefficient of road adhesion needed to achieve this acceleration

  Representative field vane shear test at a site

Estimate the maximum centric load that a 2-m-square footing can support using CSM. The minimum factor of safety is 1.25 and the settlement should not exceed 25 mm. Assume v' = 0.35.

  Determine the time when particles collide and the magnitude

the two particles A and B start at the origin O and trevel in opposite directions along the circular path at constant speeds va =.7 m/s and vb =1.5 m/s . Determine the time when they collide and the magnitude

  What is the initial pollutant flux density in x-direction

The concentration of a pollutant along a quiescent water-containing tube is shown in Figure 4-23. The diffusion coefficient for this pollutant in water is equal to 10-5 cm2 s-1.

  Determine the quantity of seepage under the piling

A deposite of soil is 16m deep and overlies an impermeable stratum , the coefficient of permiability is 10^-6 m/s. A sheet pile wall is driven to a depth of 12 m in the deposite. The difference in water level between the two sides of the piling is..

  Design a cyclone that has a collection efficiency between 80

Design a cyclone that has a collection efficiency between 80% and 85% (use parcticle size distribution given below). you must assume a dpc of 4.2 microns,an inlet gas velocity of 25 m/s and a K of 15.The unit must handle 20,000 cfm of contaminated ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd