Determine the gross inclined allowable load

Assignment Help Mechanical Engineering
Reference no: EM13947812

1. A  square  column  foundation  has  to  carry  a  gross  allowable  load  of  1805  kN sFS 5 3d.   Given:   Df  5 1.5 m,   g 5 15.9 kN/m3,   f9 5 348,   and   c9 5 0.   Use Terzaghi's equation to determine the size of the foundation (B). Assume general shear failure.

2. Use the general bearing capacity equation [Eq. (4.26)] to solve the following:

a. Problem 4.1a

b. Problem 4.1b

c. Problem 4.1c

3. The applied load on a shallow square foundation makes an angle of 208 with the vertical. Given: 55 ft, Df  5 3 ft, g 5 115 lb/ft3, f9 5 258, and c9 5  600 lb/ft2. Use FS 5 3 and determine the gross inclined allowable load. Use Eq. (4.26).

Reference no: EM13947812

Questions Cloud

Calculate xyz direct labor variances : As judged by the information contained in the performance report, should the vice president be concerned about the company's labor variances? Why?
Determine the size of the foundation : 1. For a square foundation that is B 3 B in plan, Df  5 2 m; vertical gross allowable  load,  Qall  5 3330 kN,  g 5 16.5 kN/m3;  f9 5 308; c9 5 0;  and  FS 5 4.  Determine the size of the foundation. Use Eq. (4.26).
Compute the theoretical conversion cost per unit : Compute the theoretical conversion cost per unit. Compute the applied conversion cost per unit (the amount of conversion cost actually assigned to the product).
Research issues in organizational tax research and planning : Analyze tax issues regarding corporate formations, capital structures, income tax, non-liquidating distributions, or other corporate levies - Create an approach to tax research that results in credible and current resources.
Determine the gross inclined allowable load : The applied load on a shallow square foundation makes an angle of 208 with the vertical. Given: B 55 ft, Df  5 3 ft, g 5 115 lb/ft3, f9 5 258, and c9 5  600 lb/ft2. Use FS 5 3 and determine the gross inclined allowable load. Use Eq. (4.26).
How long it take to send the file from source to destination : Suppose the network is a packet-switched datagram network, and a connectionless service is used. Now suppose each packet has 2h bits of header. How long does it take to send the packet?
Estimate the soil friction angle : The ground- water table was located at a depth of 2 m below the ground surface. Given, for the sand: gd  5 14.5 kN/m3  and gsat  5 19.8 kN/m3. The contact stress during the test was 260 kN/m2. Estimate the soil friction angle, f9.
How does water change to steam : As you have learned throughout the course, engaging young students in hands-on science experiments will enhance their knowledge in a fun and interesting way. These simple experiments will prepare them for more complex science experiences in the fut..
Graph that illustrates a recent change in law : Write a 5-paragraph essay that introduces the topic you've chosen, summarizes the various points of view, and concludes with the current status of the issue you are addressing. Be sure to use at least 2 citations to support your essay.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd