Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A superheterodyning FM receiver was originally designed and built to operate in the US only. The FM broadcasting band in the US is from 87.5 MHz to 108 MHz. The intermediate frequency of the receiver is fI = 10.7 MHz. This receiver has a poor RF BPF. (a) Determine the frequency range and the tuning ratio of the receiver LO. Can any FM channel in the US be the image station of another FM channel? Explain in detail. (b) If this receiver is brought to another country whose FM band is between 79.5 MHz and 105.1 MHz, what range of desired channels, if any, in this new country are at risk of being interfered?
HALF-ADDER: S = XY' + X'Y , C = XY (These are the outputs) 1. From the equation given for half-adder, develop an equation for which the half-adder can be constructed just with NAND gates. Draw the circuit as per the equation obtained.
Using a voltage source Vdd=2.5V and an MOSFET with Vt=0.5 V, Kn'=0.8 A/V^2, W=10um and lambda=0, build a common source amplifier which drives a load resistor of 10k ohms. The input signal to the amplifier is a sine wave with a peak value of 0.15 V..
Design a sequencer with an enabler with 3 outputs that when enabled follows a successive clock sequence of 000,000,011,011,110,110,010,011 when the last step is reached the sequence returns to the beginning.
Design the circuit to establish a dc emitter current of 1mA and provide the highest possible voltage gain while allowing for a maximum signal swing at the collector of +-2V. Use +10V and -5V power supplies.
Compare the by hand solution and the PSPICE simulation for a voltage amplifier which has an input resistance of 10kohms and an output resistance of 100ohms, and a gain of 100V/V. The voltage amplifier is capacitively coupled to a voltage source.
A 10 kVA transformer has an iron loss of 250 watts and a half-load copper loss of 80 watts. Determine the full-load efficiency at 0.8 power factor.
Design a combinational logic circuit which has one output Z and a 4-bit input ABCD representing a binary number. Z should be 1 iff the input is at least 5, but is no greater than 11. Use one OR gate (three inputs) and three AND gates
A one-dimensional infinite potential well with a width of 12 Ao contains an electron. (a) Calculate the first two energy levels that the electron may occupy. (b) If an electron drops from the second energy level to the first, what is the wavelengt..
Describe why the intrinsic carrier concentration changes with temperature. This would include from very cold temperatures to 600K+ temperatures. Why does an extrinsic semiconductor become intrinsic above ~ 500K
A clever student notices that a high constant loop gain would make the PLL converge in frequency and phase. Rather than use an amplifier with infinite gain the student decides to just use an unstable filter.
A 1000V, 50 hp compound motor runs at a speed of 750 rpm at full load. The armature, series and shunt field resistances are 0.5 ohm, 1 ohm, and 200 ohm, respectively. The motor efficiency at this condition is 80%. Calculate the motors starting cur..
Analysis of discrete time waveforms in z domain, A discrete time domain signal x(n) - u(n) - u(n-10) is decomposed and plotted. It is then examined in the z domian by appropriate transformation and algebraic manipulation.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd