Determine the force p that must be applied toi the cylinder

Assignment Help Civil Engineering
Reference no: EM13320906

The brass tube AB (E=105 GPa) has a cross-sectional area of 140 mm^2 and is fitted with a plug at A. The tube is attached at B to a rigid plate that is itself attached at C to the bottom of an aluminum cylinder (E= 72 GPa) with a cross-sectional area of 250 mm^2. The cylinder is then hung from a support at D. In order to close the cylinder, the plug must move down through 1 mm. Determine the force P that must be applied toi the cylinder.

Reference no: EM13320906

Questions Cloud

Do you think peter pundit is correct or not : If the EU and the United States continue to trade, what do you think will characterize the goods that the EU exports to the United States and the goods that the United States exports to the EU?
What would be the angular acceleration of the merry-go-round : A merry-go-round starts from rest and reaches the angular speed of 4 rpm in the first two minutes. What would be the angular acceleration of the merry-go-round
Which country has the comparative advantage in aircraft : According to the U.S. Census Bureau, in July 2006 the United States exported aircraft worth $1 billion to China and imported aircraft worth only $19,000 from China
What is the intensity of the output beam : A beam of gamma rays from a distant galaxy is observed through two polarizing filters whose transmission axis is at a 45 degree angle relative to each other here on earth. What is the intensity of the output beam
Determine the force p that must be applied toi the cylinder : The tube is attached at B to a rigid plate that is itself attached at C to the bottom of an aluminum cylinder (E= 72 GPa) with a cross-sectional area of 250 mm^2.
At what point does another year of age reduce : Person #206 in the data set has the following characteristics: cigpric = 67.44, income = 6500, educ = 16, age = 77, restaurn = 0, white = 0, smoke=0. Compute the predicted probability of smoking for this person and comment on the result
Determine the required diameter of the thread : A nylon thread is to be subjected to a 10-N tension. Knowing that E=3.2 GPa, that the maximum allowable normal stress is 40 MPA, and that the length of the thread must not increase by more than 1%
What is the operating current with the new resistor added : An electric motor is plugged into a standard 120V electrical service. At startup a current of 23.4A is measured. what is the operating current with the new resistor added
Find the temperature of the mixture : 115 g of glass beads, originally at a temperature of 75.0 oC, are added to 85.0 g of ethyl alcohol which is at a temperature of -50.0 oC. find the temperature of the mixture when thermal equilibrium is reached

Reviews

Write a Review

Civil Engineering Questions & Answers

  Angular acceleration of the spool

determine the angular acceleration of the spool and the acceleration of the trailer. The wheels have negligible mass and are free to rotate.

  Determine ft and fn

for this purpose replace this force by its equivalent of two forces at At Ft parallel and Fn perpendicular to the beam. Determine Ft and Fn.

  Determine what would the weir coefficient be

if the discharge from a 90 degree V-notch weir fills a 20 L vessel in 54 seconds and produces a stage of 30mm upstream of the weir crest, what would the weir coefficient be

  Derive the expressions for the concentration exiting a cstr

Derive the expressions for the concentration exiting a CSTR and a PFR for a zero order removal reaction. Which reactor design is more efficient in terms of volume and hydraulic retention times

  Define mechanical engineering dynamics

Important information about Mechanical engineering dynamics, A 3000 lb car rests on a horizontal street out of gas with its brakes locked.

  Compute normal and critical depths in a concrete culvert

compute normal and critical depths in a concrete culvert(n=0.015)with a diameter of 36in.and a bed slope of 0.002ft/ft if the design discharge is 15cfs.is the slope steep or mild?reap for S= 0.02ft/ft.

  Determine suitable footing dimensions to suit the bearing

Determine suitable footing dimensions to suit the bearing capacity of 100kPa with a factor of safety 2.4

  Determining axial load of a dense sand

A dense sand has an effective friction angle of 43 and c'=0. A dry, 2.8-inch diameter sample is tested in drained triaxial shear with a confining pressure of 2500 psf. What axial load, P (in pounds), will be required to fail the sample?

  Draw a cross-section of the specified pavement design

The roadway to be constructed is 3 miles long and 60 feet wide. • The following pavement design specifications have been issued: - Base coarse: 6" DGA - Stabilized base: 4" - Bottom coarse of asphalt: 3" - Top coarse of asphalt: 2"

  What is the percentage error in the bulk unit weight

What is the percentage error in the bulk unit weight if the soil is the percentage error in the bulk unit weight if the soil is 95% saturated but assumed to be 100% saturated

  Calculate the compressive normal stress in the bar

A stainless steel (304) bar with a cross section of 0.2" x 0.4" is cut to a length of 30" and placed between two immovable walls at a  temperature of 40 degrees F. The operating temperature for the bar is 200 degrees F.

  When will drivers be able to see the full sign

A roadway has a 4% grade intersecting a -7% grade at at station 18+50.00. The grades are connected by an 800 foot vertical curve. A sign is proposed to be installed at Station 15+00.00. The bottom of the sign is 7 feet above the roadway.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd