Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 25-mm diamenter shaft is pulled through a cylindrical bearing. The lubricant that fills the 0.3-mm gap between the shaft and bearing is an oil having a kinematic velocity of 8.0x10^-4 m^2/s and a specific gravity of 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear. Note: picture not shown but length is 0.5m. This is also question 1.38 in the 4th edition-The one that is poping up is not the right one.
The total dissolved inorganic carbon (TIC) of a sample of groundwater is 8.33 mM. The temperature of the aquifer is 15C, the pH is 7.5, and the ionic strength is 0.05 M. What is the H2CO3, HCO3-, CO3 2-, and the partial pressure of CO2? [Use activ..
Finally, the wreckage is removed, and the freeway is restored to full capacity (4000 veh/h) at 8:31 a,. Assume D/D/1 queuing to determine time of queue dissipation, longest queue length, total delay, average delay per vehicle, and longest wait of ..
determine the length of an interval of time such that the probability of at least one call in the interval is 0.90
Water at 20ºC flows at a velocity of 2 m/s in a 200-mm diameter horizontal ductile-iron pipe. a) Estimate the friction factor in the pipe, and state whether the pipe is hydraulically smooth or rough.
You are in an old spy movie, and have been locked into a small room (volume 1000 ft). You suddenly realize that a poison gas has just started entering the room through a ventilation duct.
Consider CO2 emissions from a gasoline powered vehicle. Gasoline is acomplex mixture of hydrocarbons but for the purposes of this calculation assume an average molecular formula of C7H16.
Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.
A pool of benzene is ignited on the floor of a large industrial building. The total area covered by the Kerosene pool is 6 meters square (Note that this is considered a large pool D>0.2 meters). Combustion efficiency is 70%. Estimate the plume mas..
The three blocks shown move move with constant velocities. Find the velocity of each block, knowing that the relative velocity of A with respect to C is 300 mm/s upward and that the relative velocity of B with respect to A is 200 mm/s downward.
A vertical curve is designed for 55 mi/h and has aninitial grade of +2.5% and a final grade of 1.0%. The PVT is at station 114 + 50. It is known that a point onthe curve at station 112 + 35 is at elevation 245 ft.
Air can be assumed as a di-atomic ideal gas. Find the final temperature and the amount of work ( in kW) required for air compression at a rate of 100 mol/s , from an initial condition of 1 bar an 25 C to 10 bar; for the following ways:
A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd