Determine the force of mutual gravitational attraction

Assignment Help Mechanical Engineering
Reference no: EM131381294

The mass of the Moon is approximately 7:35 ×1022 kg, and its mean distance from the Earth is about 3:80 × 108 km. Determine the force of mutual gravitational attraction in newtons between the Earth and Moon. In view of your answer, discuss why the Moon does not crash into the Earth.

Reference no: EM131381294

Questions Cloud

Calculate the amounts of the given ratios : Calculate the amounts of these ratios for 2012. Assess the changes in the short-term liquidity risk of Techtron between 2010 and 2012 and the level of that risk at the end of 2012.
Management leadership and employee participation : "Management Leadership and Employee Participation" has been said to be the most important section of the ANSI/AIHA Z10 standard. Provide your opinion as to which section might be the second most important. Support your discussion with examples fro..
Health law and bioethics-cases in context : Carefully read United States v. Krizek (pages 187-205) in Health Law and Bioethics: Cases in Context Dr. Krizek contend throughout the litigation that he was a victim of "a blatant injustice" perpetrated against a dedicated foreign-born practition..
Read the case study entitled appraising employees : Read the Case Study entitled, "Appraising Employees at the San Diego Zoo" on pages 386-387 in Chapter 8 (Case Study 2). Then, answer all of the questions at the end of the case.I selected the most interesting and applicable cases for the class. Pl..
Determine the force of mutual gravitational attraction : Determine the force of mutual gravitational attraction in newtons between the Earth and Moon. In view of your answer, discuss why the Moon does not crash into the Earth.
Article review - the ottawa way thrives : Article Review - Critically review the article below: In the review, be sure to include an analysis of the article. Provide details and evidence to back up your analysis from the article
Are conclusions valid for all types of crude oil : Are conclusions valid for all types of crude oil? What assumptions are necessary for the analysis? Do you believe that all the assumptions are met in this case? What are the limitations, if any, of this study? Discuss.
What healthcare organizations-departments are impacted : Identify one challenge you see in the U.S. health care system today. What healthcare organizations/departments are impacted?
Organizational strategies for management of innovation : Chris is the health care administrator for Health Innovations South, a large network of regional hospitals and care centers that provide direct patient care and engage in health research. In a recent market analysis, Chris discovered that Health I..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the pressure in the vessel and the enthalpy

Water is contained in a 0.2 m3 vessel at 200 C. The mass of water in the vessel is measured to be 2 kg. Determine (a) the pressure in the vessel, (b) the enthalpy, h, of the water in kJ/kg, (c) the mass and volume of vapor in the vessel.

  Determine the smallest force p that should be applied

Knowing that the coefficient of static friction is 0.30 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges.

  Q1 figure shows a scale drawing of the temperature profile

q1 figure shows a scale drawing of the temperature profile through a composite plane wall.i identify the layer with the

  Air is compressed under steady flow conditions see figure

air is compressed under steady flow conditions see figure q3. the power input to the compressor is 3 kw. during the

  Assuming neglible heat transfer between the bucket and the

a one kg metal part specific heat 0.7 kjkg k initially at 1234k is quenched in a bucket containing 20 gallons of water

  The center lines of hte inlet and discharge pipes are at

a turbine is supplied with 0.6m3s of water from a 0.3m diameter pipe the discharge pipe has a diameter of 0.4m. the

  A prismatic bar is subjected to loads that cause uniform

a prismatic bar is subjected to loads that cause uniform axial strains epsilon0.002 in its left half and epsilon-0.004

  The change in specific entropy between the specified states

Determine the change in specific entropy between the specified states, in kJ/kg·K. Water, p1 =10MPa, T1 =400°C,p2 =10MPa, T2 =100°C. Air asanidealgas,p1 =200kPa, T1 =7°C,p2 =100kPa, T2 =327°C.

  Determine the following for a south-facing surface

Determine the following for a south-facing surface at 30° slope in Gainesville, Florida (latitude = 29.68°N, longitude = 82.27°W) on September 21 at noon solar time

  A turbine takes in 2 kgs neon at 27 degc and 200kpa with

a turbine takes in 2 kgs neon at 27 degc and 200kpa with negligible velocity. the produced work is 75 kw and 30 kw of

  Determine the frequency response

A causal discrete-time LTI system is described by y [ n ) - h [ n - 1) + !Y [ n - 2) = x [ n ) where  x[ n ] and  y[ n ] are the  input  and  output  of  the  system,  respectively.

  Explain project management concepts and benefits

New Century Wellness Group offers a holistic approach to healthcare with an emphasis on preventive medicine as well as traditional medical care. In your role as an IT consultant, you will help New Century develop a new information system.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd