Determine the force in members gf-fb and bc

Assignment Help Civil Engineering
Reference no: EM13309998

determine the force in members GF,FB, and BC of the Fink truss and state if the members are in tension or compression?

Reference no: EM13309998

Questions Cloud

Draw one child diagram using the level 0 diagram : As a systems analyst or knowledgeable end-user, you must learn how to draw data flow diagrams to model business process requirements.
What length tube is required : Bubba has a tuning fork with a frequency of 445 Hz. Assuming the speed of sound in his lab is 350. m/s, what length tube is required to find the resonant point of his fork
Determine the minumum coeffeicient of friction : A water jet of diameter 2 inches and speed of v=60 ft/s is filling a tank at a 70 degree angle. The tank has a mass of 25 lbm and contains 6 gallons of water. The water temperature is 70 degrees F.
Explain malonic acid titrated with naoh : Malonic acid titrated with NaOH.,what indicator could be used to find the endpoint,If there is more than once choice, which is best
Determine the force in members gf-fb and bc : determine the force in members GF,FB, and BC of the Fink truss and state if the members are in tension or compression
What is the energy efficiency rating of the unit : A window air-conditioner unit absorbs 9.70×104J of heat per minute from the room being cooled, What is the energy efficiency rating of the unit
Determine what is the deflection at the center of the beam : A C10x20 catilever beam is 12 feet long, supported on the right side. The beam supports two point loads: Load 1 is 2500 lbf and is located 2.5 feet from the wall. Load 2 is 1300 lbf and is located 12 feet from the wall.
Compute the thermal efficiency of the engine : A diesel engine performs an amount of mechanical work equal to 2800Jand discards an amount of heat equal to 4800J each cycle. What is the thermal efficiency of the engine
What is the delfection due to self weight at the end of beam : A 13 foot long C10x25 beam is supported as a cantilever beam where x=0 on the left end. It is subject to no externally applied loads. a) What is the delfection due to self weight at the end of the beam

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute required weight of coarse aggregate per cubic yard

A concrete mix witha 3-inch slump, w/c rtion of .5, ans sand with a fineness modulus of 2.4 contains 1700 lb/yd^3 of coarse aggregate. compute the required weight of coarse aggregate per cubic yard.

  How much power is required to overcome aerodynamic drag

A new sports car has a drag coefficient of .30 and a frontal area of 21 ft^2, and is traveling at 110 mi/h. How much power is required to overcome aerodynamic drag if p=.002378 slugs/ft^3?

  Determine the corresponding value

Link ABrotates through a limited range of angle β, and its end Acauses the slotted link ACto rotate also. For the instant represented where β= 60 and = 0.6 rad/sconstant, determine the corresponding value of r r'.

  Compute the percent voids in total mix and percent voids

An aggregate blend is composed of 59% coarse aggregate by weight (sp. Gr. 2.635), 35% fine aggregate (Sp. Gr. 2.710), and 5% filler (Sp. Gr. 2.748). The compacted specimen contains 6% asphalt binder

  Determine the principal stresses and the principal angle

using the stress transformation quations only,given a stress state where sigma x=6500 psi,sigma y= 17,300 psi and tau xy=2900 psi, determine the principal stresses,the principal angle and the maximum shear stress.

  Determine the distance s that the top hoop should be placed

The barrel has an inner diameter of 4ft. Neglect its wall thickness. Assume that only the hoops resist the water pressure. Note: Water develops pressure in the barrel according to Pascal's Law, p=62.4 lb/ft^2, where z is the depth from the surface..

  Calculate the maximum mounding height from the canal

If the hydraulic head in the canal is 100 ft and in the drainage ditch it is 80 ft calculate the maximum mounding height and the mounding distance from the canal that will occur if the farmer irrigates at a rate of 2 acre-ft/acre/year.

  Design a needle-punched nonwoven geotextile for use

The thickness of geonet is 0.2 inch (5 mm). Assume the maximum inflow rate is 0.14 inch/hour. The liquid head over the geomembrane liner is 2 inches. The index properties of the soil placed over the geotextile are as follows

  Number of completely mixed bioreactors

Determine the number of completely mixed bioreactors (detention time of 45 min each) that would be required to meet the phenol discharge limit of 5 mg/L. The first-order removal rate constant is equal to 6.1 hr -1

  What is stress to load ratio at depth of 2b below the centre

for a uniformly loaded square area, what is the stress to load ratio at a depth of 2B below the CENTER of the loaded area

  Estimate the change in pressure over 100 m of pipeline

Water at 20 degrees flows at a velocity of (V =) 2 m/s in a (D =) 250-mm diameter horizontal ductile iron pipe. Estimate the friction factor f in the pipe, and state whether the pipe is hydraulically smooth or rough.

  Find what design speed was used for a freeway exit ramp

a freeway exit ramp has a single lane and consists entirely of a horizontal curve with a central angle of 90 degrees and a length of 628 ft. if the distance cleared from the centerline for sight distance is 19.4ft, what design speed was used

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd