Determine the force in cable cbd

Assignment Help Mechanical Engineering
Reference no: EM131384149

Due to settlement of soil, a recently planted tree has started to lean. To straighten it, the cable system shown is used, where a turnbuckle on cable AB is periodically tightened to keep the cable taut as the tree gradually straightens. If the force in cable AB is 450 N, Figure P3.15 determine the force in cable CBD.

1193_7858e828-6d0e-4dce-a44d-04665c4dc880.png

Reference no: EM131384149

Questions Cloud

Identify the independent variable and its levels : Identify each of the following as an independent-samples design or a paired-samples design. For each, identify the independent variable and its levels and the dependent variable.
Decide on a one or two tailed test : All observers are successful; the search time for each is given in the table in minutes. Decide on a one- or two-tailed test, analyze the data, and write a conclusion.
Find the largest distance d the concrete pipe may be moved : A crane is used to lift a concrete pipe weighing 5 kN into place. For precision positioning, the worker at C can apply up to a 400 N force to cable AC. Determine the largest distance d the concrete pipe may be moved.
Give the answer of muliple choice question : CPS 541: A major difference between group therapy and group counseling lies in:Which type of group focuses on remediation, treatment, and personality reconstruction?What does a member have a right to expect before making the decision of whether or no..
Determine the force in cable cbd : If the force in cable AB is 450 N, Figure P3.15 determine the force in cable CBD.
Write a conclusion about the effect of a 20 percent : Analyze the data in the table and write a conclusion about the effect of a 20 percent loss of cortex on retention of memory for a simple maze.
Determine the forces in cables acb and cde : The symmetric cable and pulley arrangement shown is used to lift a fragile architectural stone beam. If the only significant mass in the system is the 800 kg mass m of the beam, determine the forces in cables ACB and CDE.
Analyze data which are in minutes and write a conclusion : After training, each employee completed a search report on 40 products. Analyze the data, which are in minutes, and write a conclusion about the new software package.
Give the answer of muliple choice question : Terry developed an intense fear of riding motorcycles 2 years ago when he was injured in a major accident. Today, after numerous, uneventful motorcycle rides, he can again drive without distress. Which of the following best describes what has happ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assuming the air behaves as an ideal gas with cv 072 kjkg-k

2 m3 of air in a rigid and insulated container that is fitted with a paddle wheel assembly. the air starts at 300 k and

  Determine the horizontal component of the absolute velocity

the 90-kg man dives from the 40-kg canoe. the velocity indicated in the figure is that of the man relative to the canoe

  Determine the compressive force that must be applied to heat

Determine the compressive force that must be applied to heat the joint to the Inconel melting point within t 3 s, starting from an initial temperature of 20°C.

  Rate of heat transfer through sheet of insulation

The thermal conductivity of a sheet of rigid, extruded insulation is reported to be k = 0.029 W/m· K. The measured temperature difference across a 20-mm-thick sheet of the material is T1 - T2 = 10° C.

  Determine the number of cycles per minute

Determine the number of cycles per minute

  Power plant generates steam from coal burning

A power plant generates steam from coal burning which burns at 3,000oF and produces about 13,000 BTU per pound. The steam is put into a poorly insulated turbine which allows 2,000 BTU per pound of coal to escape to the atmosphere at 90oF. Knowing the..

  Differences between an attack and a threat

In computer security terms, explain the differences between an attack and a threat.

  A power cycle operates between a reservoir at temperature t

a power cycle operates between a reservoir at temperature t and a lower temperature reservoir at 280ok. at steady state

  A sealed rigid tank contains 50 kg of water liquid plus

a sealed rigid tank contains 5.0 kg of water liquid plus vapor at 100degc with a quality of 30.375.a. calculate the

  The ultimate strengths in tension and compression are 210

a thin-walled cylindrical pressure vessel of 250 mm internal diameter and 5 mm thickness is subjected to an internal

  Compute the radius of curvature of the dip in the road at b

If the magnitude of the total acceleration of the mass center of the car is the same at B as at A, compute the radius of curvature of the dip in the road at B. The mass center of the car is 0.6 m from the road.

  Determine the axial stress required to induce this strain

An aluminium bar is subjected to uniaxial tensile loading. If the lateral strain (perpendicular to the load direction) is measured to be -0.00025, determine the axial stress required to induce this strain (round to the nearest ksi).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd