Determine the flow rate in the pipeline and the head loss

Assignment Help Civil Engineering
Reference no: EM13560460

Contract loss coefficient = Kc = 0.34 , d1 = 2 in , d2 = in d3 = 1 in , and Rm = 6ft , gauage fluid = 52lbf/ft^3 neglect friction but consider an expansion loss coefficient of k' = o.5

Draw the hydraulic grade line and envergy line between datum 1 and 3

Determine the flow rate in the pipeline and the head loss between datum 1 and 3

Find the total force on bolts

Reference no: EM13560460

Questions Cloud

Sketch the equipotential line going through the origin : Flow velocity is given by the function v= -5i +3j . Find the equation for the velocity potential, and the stream function ?. Sketch the equipotential line going through the origin.
One side slope extends to a height of 7.8 m above the bottom : A uniform earth canal in good condition is 17 m wide at the bottom and has side slope of 2 horizontal to 1 vertical. One side slope extends to a height of 7.8 m above the bottom level and the other side extends to an elevation of 1.8 m then extends t..
What the order of accuracy of this operator : You are given five data points, yi = f(xi), where i ranges from -2 to 2, and where xi+1 ? xi = ?x is a constant. You are interested in computing the first and second derivative of f at x0.
Determine the operating point on the pump characteristic : Determine the operating point on the pump characteristic curve when the flow is such that the pressure drop across the control valve is 35 kN/m^2
Determine the flow rate in the pipeline and the head loss : Contract loss coefficient = Kc = 0.34 , d1 = 2 in , d2 = in d3 = 1 in , and Rm = 6ft , gauage fluid = 52lbf/ft^3 neglect friction but consider an expansion loss coefficient of k' = o.5
Calculate the steady state hcho concentration : These concentrations were measured when the trailers were 2 years old and the emission rate had significantly decreased by that time. New material rates as high as 290 mg/hr have been reported. Calculate the steady state HCHO concentration (ug/m3) re..
How efficient is the pump : A fireboat pump draws seawater (density=1.95 slugs/ft^3) from a 6 inch diamter submergred pipe that reaches 6 feet under the free surface and discharges 120 ft/s through a 2 inch diamter nozzle 10 feet above the free surface
Find the rate of biological growth : Two identical complete-mix activated sludge units are connected in series; one-half of the sludge recycle flow rate, QR, is recycled to the primary effluent pipeline which handles a flow rate Q, and the other half is recycled to the effluent line fro..
Which alloy and in what condition whould you choose : For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender

Reviews

Write a Review

Civil Engineering Questions & Answers

  A pipeline terminates in a nozzle of outlet diameter 015 m

a pipeline terminates in a nozzle of outlet diameter 0.15 m. the free jet from the nozzle is deflected through

  What are the bearings of the sides

Why is the torque on A and the torque on AB opposite? Wouldn't they be the same? How do we know which direction the torque is applied at A to begin with? It's not specified.

  To orient a transit in azimuth when the transit is set up

To orient a transit in azimuth when the transit is set up over a point D, a backsight is taken to another point, C, with vernier A set at the azimuth of the line CD and with the telescope in its inverted position

  What is the residence time of air in the room if rate is use

On average each student produces 1 kg of carbon dioxide per day. The recommended ventilation rate of fresh air to avoid excessive carbon dioxide buildup is 8 L per second per student.

  Determine the speed of each car just after the collision

The 15-Mg tank car A and 25-Mg freight car B travel towards each other with the velocities. If the coefficient of restitution between the bumpers is e=0.6, determine the speed of each car just after the collision.

  How many 1-inch diameter steel bolts are required to hold

The two cylinder containers are joined by bolting their flanges together. How many 1-inch diameter steel bolts are required to hold the cylinders together when the assembly is subjected to an internal pressure of 200 psi

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  Determine percentage of truck as seen by stationary observer

From a photograph one observs that on a level section of highway 20% of the vehicles are trucks, 80% are cars, and that there are 50 vehicles per mile of highway. The trucks travel at 40 mph, the cars at 50 mph.

  What is the distance uncertainty at the surface of ellipsoid

if a hand-held GPS unit locates a latitudinal position with an uncertainty of + - 0.02-seconds, what is the distance uncertainty at the surface of the ellipsoid.

  Describe some of characteristics of the fe-c transformation

(a) Describe the following types of Fe-C martensites that occure in plain-carbon steels: (i) lath martensite, (ii) plate martensite. (b) Describe some of the characteristics of the Fe-C martensite transformation

  Determine the speed of the block after it has compressed the

A 20 kg block slides along the rough surface for which the coefficient of kinetic friction is 0.2. The block strikes a nonlinear spring with a speed of v=4.5 m/s. The spring is termed

  How many particles would be present in a cubic meter

How many particles would be present in a cubic meter of aerosol at the concentration of the U.S. PM-10 standard or 50 micrograms/cubic meter if the particles are .1 micrometer in diameter.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd