Determine the final volume of the argon

Assignment Help Mechanical Engineering
Reference no: EM13717701

One cubic meter of argon initially at 300 K is compressed such that the change in the specific enthalpy is -0.27 kJ/kg-K and the temperature is reduced 100 K. Determine the final volume of the argon. (k = 1.67)

Reference no: EM13717701

Questions Cloud

Define what volume of solution do i have in a flask : What volume of solution do I have in a flask if the empty flask weighs 250g, the total flask with solution weighs 320g, and the density of the solution is 1.5g/ml
The data for per capita income in thousands of us : The following table gives the data for per capita income in thousands of US dollars with the percentage of the labor force in Agriculture and the average years of schooling of the population over 25 years of age for 15 developed countries in 20..
Explain what is the molarity of a phosphoric acid stock used : What is the molarity of a phosphoric acid stock used to make 750ml of a dilute 4M solution if 52ml of the stock was used?
Calculate the adjusted retention volume of the analyte : In a capillary GC separation the analyte of interest elutes at 7.2min, and the unretained peak elutes at 2.2min. Given column dimensions of 30m x 0.5mm ID, calculate the adjusted retention volume of the analyte.
Determine the final volume of the argon : One cubic meter of argon initially at 300 K is compressed such that the change in the specific enthalpy is -0.27 kJ/kg-K and the temperature is reduced 100 K. Determine the final volume of the argon. (k = 1.67)
Company w is testing a sales software : Company W is testing a sales software. Its sales force of 500 people is divided into four regions: Northeast, Southeast, Central, and West. Each sales person is expected to sell the same amount of products. During the last 3 months, only half ..
Explain what is the molar concentration of mg2+ in solution : Suppose 286 mL of 0.215 M MgCl2 is mixed with 173 mL of 0.382 M NaOH and allowed to react completely. Volume change at precipitation can be ignored.
Develop an expression for the velocity profile of the fluid : A viscous fluid flows under its own weight between two very wide, stationary, flat plates inclined at an angle theta to the horizontal. Develop an expression for the velocity profile of the fluid assuming fully developed steady, laminar flow
Define what volume of the enzyme stock solution : You has a stock solution of enzyme (125 kD) at a concentration of 1mg/ml. You want to achieve a final enzyme concentration of 36nM in a 1ml reaction volume. What volume of the enzyme stock solution will you add to the reaction

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd