Determine the final temperature of the air in the cylinder

Assignment Help Mechanical Engineering
Reference no: EM13610965

A frictionless piston-cylinder device fitted with stops above the piston contains 1.2 kg of air at 200°C and 700 kPa. This pressure is sufficient to ensure that the piston is pressing up against the stops. A valve at the bottom of the cylinder is now opened, and air escapes from the cylinder. Just as the air pressure reaches exactly 600 kPa, the piston is observed to begin to move downwards. The valve is closed when the cylinder volume has declined to 80% of its initial volume. During the air loss process, 40 kJ of heat is lost from the cylinder. Determine (i) the final temperature of the air in the cylinder, (ii) the work done, (iii) the mass of air that has escaped from the cylinder, and (iv) answer the question that's given at the end of the following hint. Use ‘best guess' constant specific heat values at the average temperature.

Reference no: EM13610965

Questions Cloud

Calculate the weight percentage of primary alpha phase and : give the schematic representation of the equilibrium microstructures for a lead-tin alloy of composition 45 wt of tin
In nov 04 the firm said that it might default on certain of : friedmans inc is a leading fine jewellery retailer.in nov 04 the firm said that it might default on certain of
Kleener co acquired a new delivery truck at the beginning : kleener co. acquired a new delivery truck at the beginning of its current fiscal year. the truck cost 26000 and has an
The standard cost for making 1 item of brand x is 8 hours : the standard cost for making 1 item of brand x is 8 hours at 9 per hour 72 total. the actual cost was 7 hours at 10
Determine the final temperature of the air in the cylinder : a frictionless piston-cylinder device fitted with stops above the piston contains 1.2 kg of air at 200degc and 700 kpa.
Greek company produces and sells 22000 units of a single : greek company produces and sells 22000 units of a single product. costs associated with this level of production are as
Clean all inc sells washing machine with a three : clean all inc. sells washing machine with a three yearwarranty. in the pastclean all has found that in the year
Determine a the minimum diameter of the inlet pipe in cm so : ammonia enters a control volume operating at steady state at p1 14 bar t1 28 oc with a mass flow rate of 0.5 kgs.
Assume that adults have iq scores that are normally : assume that adults have iq scoresthat are normally distributed with a mean of 100 and a standard deviation of 15 as on

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd