Determine the final pressure in the tank

Assignment Help Mechanical Engineering
Reference no: EM13707043

Consider 0.8 grams of air (which may be assumed to be an ideal gas) at 295 K and 1.5 bar trapped in a rigid tank. An electrical heater is operated for 30 seconds. During this time the voltage across the heater is 12 V and 0.6 amps pass through the resistance element. During this process, 126 J of energy is lost via heat transfer through the tank walls.

Assuming the specific heats of air are constant (at the 300 K values (use table B.9)) determine the final temperature of the air. Hint: Use the prop. relationships.

Determine the final pressure in the tank.

Reference no: EM13707043

Questions Cloud

Obtain the speed of the stone just before it hits the ground : You throw a stone vertically upward with an initial speed of 6.0m/s from a third-story office window. Find the speed of the stone just before it hits the ground
How far is he from the starting point : A jogger runs directly east for 5 km, then turns and goes northwest for 5 km. He then travels directly south for 3 km. How far is he from the starting point
Calculate the magnitude of the torque on the dipole : An electric dipole consists of charges +2e and -2e separated by 0.89 nm. It is in an electric field of strength 4.4 x 106 N/C. Calculate the magnitude of the torque on the dipole
What are the fractions of muscle and fat in the leg : It's possible to estimate the percentage of fat in the body by measuring the resistance of the upper leg rather than the upper arm; the calculation is similar. What are the fractions of muscle and fat in the leg
Determine the final pressure in the tank : Consider 0.8 grams of air (which may be assumed to be an ideal gas) at 295 K and 1.5 bar trapped in a rigid tank. An electrical heater is operated for 30 seconds. During this time the voltage across the heater is 12 V and 0.6 amps pass through the re..
What is the initial velocity of the ball in the y direction : A baseball is hit at ground level. The ball is observed to reach its maximum height above ground level 2.5 seconds after being hit. What is the initial velocity of the ball in the y direction
Calculate the specific heat at constant pressure : Calculate the specific heat at constant pressure (cp) and the specific heat and constant volume (cv) for air (jama = 1.4 ). The gas constant is given as R= 8.31446 J/molK.
How far apart are they after 1.8 h : Two airplanes leave an airport at the same time. The velocity of the first airplane is 720 m/h at a heading of 12.6 degrees. How far apart are they after 1.8 h
Obtain the equivalent spring constant of the rubber bands : A slingshot consists of a light leather cup attached between two rubber bands. It takes a force of 28 N to stretch the bands 1.3 cm. What is the equivalent spring constant of the rubber bands

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At what temperature will the steam start to condense when

a rigid container is filled with steam at 700 kpa and 200oc. at what temperature will the steam start to condense when

  A feedwater heater uses extracted steam p1500kpax1100 to

a feedwater heater uses extracted steam p1500kpax1100 to preheat feedwater t250 celcius p2500kpa. assuming no heat

  Ammonia vapor flows through a valve it enters the valve at

ammonia vapor flows through a valve. it enters the valve at a pressure of 8 bar and a temperature of 120c and after

  Determine the magnitude of the average friction force

the 3.25-kg collar shown below is attached to a spring and released from rest at a. the collar then travels downward a

  A four-cylinder engine with a 95-cm bore and an 875-cm

a four-cylinder engine with a 9.5-cm bore and an 8.75-cm stroke has a 7 clearance. the engine rotates at 2500 rpm. the

  A cold storage room has walls made of 023 m of brick on the

a cold storage room has walls made of 0.23 m of brick on the outside 0.08 m of plastic foam and finally 1.5 cm of wood

  A surface area of 15 m2 find the final volume of the argon

a rigid tank of volume 6 m3 contains argon at 500 kpa 30oc. it is connected to a piston cylinder initially at the

  Determine the angular velocity

Determine the angular velocity of the two 10-kg rods in Fig. 2 when , if they are released from rest in the position . Neglect friction.

  A 4m long quarter-circular gate of radius 3 m and of

a 4m long quarter-circular gate of radius 3 m and of negligible weight is hinged aboutnbspits upper edge a. the gate

  The exit pressure is atmospheric and the diameter is 01 m

a 180 degree elbow takes in water density water 1000 kgm3 at an average velocity of 1 ms at the horizontal inlet where

  Calculate the break hp of the pump using water

Using a centrifugal pump, and a flow rate of 60 gal/min, calculate the break hp of the pump using water with a density of 62.4lbm/ft3 and do the same for a nonviscous liquid having a density of 0.85g/cm3.

  What are the temperature on the left edge of the wall the

a one dimensional wall of material kw10wmk is 50 mm thick with uniform heat generation qlsquolsquolsquo5106wm3. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd