Determine the final pressure and temperature

Assignment Help Mechanical Engineering
Reference no: EM13707782

A piston/cylinder assembly in a car contains 12 in3 of air at 13 lbf/in2 and 68 F. The air is compressed in a polytropic process with exponent n = 1.25 to a final volume six times smaller. Determine the final pressure and temperature, and the heat transfer of the process

Reference no: EM13707782

Questions Cloud

Find the voltage across the capacitor : A 12-V battery is connected to three capacitors in series. The capacitors have the following capacitances: 4.6uF , 11uF , and 30uF. Find the voltage across the 30 uF capacitor
Determine the heat transfer during the process : A tank of 20 ft3 volume is half-filled with liquid water, and the remainder is filled by vapor at 550 psia. The water is heated until one-half of the liquid (by volume) is evaporated, while an automatic valve lets saturated vapor escape at such a rat..
How high above the ground was the acorn before it fell : You attach a meter stick to an oak tree, such that the top of the meter stick is 1.27 meters above the ground. If the acorn takes 0.316 seconds to pass the length of the meter stick, how high above the ground was the acorn before it fell
What are the advantages of conducting a cost-benefit : What are the advantages of conducting a cost-benefit analysis on a new health care service an insurance company is considering, such as screening for prostrate cancer as a covered benefit?   Support your answer with References
Determine the final pressure and temperature : A piston/cylinder assembly in a car contains 12 in3 of air at 13 lbf/in2 and 68 F. The air is compressed in a polytropic process with exponent n = 1.25 to a final volume six times smaller. Determine the final pressure and temperature, and the heat tr..
Probabilistic activity time estimates are for a cpm : The following probabilistic activity time estimates are for a CPM/PERT network. Time Estimates (days) Time Estimates (days) Activity a m b Activity a m b 1 1 2  6  7 1 1.5 2 2 1 3  5  8 1 3 5 3 3 5 10  9 1 1 5 4 3 6 14 10 2 4 9 5 2 4  9 11 1 2 3 6 ..
Calculate the heat transfer in the process : A cylinder fitted with a frictionless piston contains 2 kg of superheated refrigerant R-134a vapor at 350 kPa, 100oC. The cylinder is now cooled so that the R-134a remains at constant pressure until it reaches a quality of 75%. Calculate the heat tra..
How much time do the workers have to get to the piano : A piano has been pushed to the top of the ramp at the back of a moving van. The workers think it is safe, but, as they walk away, How much time do the workers have to get to the piano
Propulsion scheme calls for use of liquid nitrogen as fuel : A new vehicle propulsion scheme calls for the use of liquid nitrogen as "fuel". The details of the power cycle are basically liquid nitrogen is heated in contact with the atmosphere, pressurised and expanded through a turbine) .

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd