Determine the filtration rate if the depth of this layer

Assignment Help Civil Engineering
Reference no: EM13559224

A Single clean layer of sand in a rapid-sand filter has an average grains size of 20X40 US. Mesh, porosity go 0.4, sand specific gravity of 2.65, and shape factor of 0.85. The absolute viscosity and density of water are 1.4X10^-3 Pa-s and 998 kg/m^3, respectively. For a head loss of 0.1 m, determine the filtration rate (m/d) if the depth of this layer of sane is 0.1m?

Reference no: EM13559224

Questions Cloud

Determine the number of kilograms of chlorine needed per day : Consider again the proposed water treatment plant for a city of 100,000 people where the maximum daily water usage rate is 99 X 106 L/d. Determine
What is the percent removal of two particles with settling : What is the percent removal of two particles with settling velocity of 0.001 and 0.002 m/s in the sedimentation basin is the basin is (i) a rectangular tank and (ii) an up flow clarifier?
Evaluate the average blood speed : The volume flow rate in an artery supplying the brainis 3.6*10 -6 m3/s. If the radius of theartery is 5.3 mm, determine the average blood speed
Who is the target audience in translating : Who is the target audience in Translating Translation by Alberto Rios?
Determine the filtration rate if the depth of this layer : A Single clean layer of sand in a rapid-sand filter has an average grains size of 20X40 US. Mesh, porosity go 0.4, sand specific gravity of 2.65, and shape factor of 0.85. The absolute viscosity and density of water are 1.4X10^-3 Pa-s and 998 kg/m^3,..
What is the minimum detention time in hours to settle out : The settling velocity of alum floc in a sedimentation basin is approximately 0.0014 fps. Calculate the equivalent overflow rate in gpd/ft2. What is the minimum detention time in hours to settle out the alum floc in an ideal basin with a depth of 10 f..
Developing a greater understanding of the meaning : How is understanding this element important to developing a greater understanding of the meaning of the work? In what ways does the element advance themes in the work?
Evaluate the diameter of the circle : A point source of light is 112 cm below the surface of a body ofwater. Find the diameter of the circle at the surface throughwhich light emerges from the water
Which of these would you consider to be inappropriate : Fluids (water, air etc) are known as 'incompressible'. which of these would you consider to be inappropriate?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the difference in reservoir elevations for 20 cfs

The characteristics of the line are 5,000 ft of steel pipe (e = 0.00015 ft) which has an ellipsoidal cross section (flow area = 4 ft^2; wetted perimeter = 8 ft); three standard elbows (K = 0.9 per elbow); a globe valve (K = 10); and a re-entrant p..

  If variable y is defined obtain y in terms of c

Consider the following two simultaneous equations: x^2 + y^2 = 42x + 3*y + 2*y^2= 6 Which of the following is a possible solution for x and y? Answer x = -6.22 & y = 1.83 x = 6.48 & y = 0.18 x = -5.59 & y -1.38 x = 6.33 & y = -3.27

  Depth of aggregate of wheel load over soil

A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees?

  Compute the percent change n in the normal forces at a

During an engine test on the ground, a propeller thrust T = 4000 N is generated on the 1500 kg airplane with mass center at G. The main wheels at B are locked and do not skid; the small tail wheel at A has no brake.

  Smooth concrete and the flow gain if the highest capacity

A 40-cm straight pipe is used to carry water at 20 degrees C from resevoir A to resevoir B that is 0.7 km away. There is an elevation difference of 9-m between the two resevoirs. Determine the discharge for

  Design the weir structure in order to accommodate the design

Along the length of the channel the bed drops by an average of 2.5 metres every kilometre. Historic accounts indicate that the maximum flow of water in the channel prior to the construction of the gauging structure was 1.4 m.

  Calculate the approximate alkalinity of water containing ion

Calculate the approximate alkalinity (in mg/L as CaCO3) of a water containing 120 mg/L of bicarbonate ion and 15 mg/L of carbonate ion.

  Explain how to verify that the third central moment is zero

Write a computer program that generates a sequence of random variables from a normal distribution with mean 5 and standard deviation 2. a) Verify that sample mean and the sample variance converge to the respective population values.

  Determine the controlling ct factor at the water temperature

A small city is evaluating disinfection requirements for their drinking water plant. With an average flow of 5 MGD and a peak flow of 9 MGD, determine the controlling CT factor (virus or giardia) when the water temperature is 23 degrees C.

  Determine the required cross sectional area of the cables

The magnetic declination at a certain place is 12 degree 6 minutes W.What is the magnetic bearing there (a) of true north (b) of true south and (c) of true west?

  Determine what is the present worth of the investment

Aerotron Electronics is considering purchasing a water filtration system to assist in circuit board manufacturing. The system costs $40,000. It has an expected life of 7 years at which time its salvage value will be $7,500.

  How many gallons would be required to last same time as gas

A water treatment plant effluent is to be disinfected with chlorine from ton cylinders of compressed gas. The plant is 5 million gallons per day. There are a total of 10 useable cylinders in the plant.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd