Determine the exit temperature of the air

Assignment Help Mechanical Engineering
Reference no: EM13719103

Air enters the evaporator section of an air-conditioner at 100 kPa, 27 C with a volumetric flow rate of 6 m^3 /min. R-134a enters the evaporator at 120 kPa with a quality of 0.3 and rate of 2 kg/min and it leaves as a saturated vapor at the same pressure. Determine (a) the exit temperature of the air and (b) the rate of entropy production (kW/K) for the process in two ways: (i) Assume the outer surface of the evaporator is insulated. (ii) Assume the outer surface is not insulated and heat is transferred from the surrounding medium which is at 32 C to the evaporator at a rate of 30 kJ/min.

Reference no: EM13719103

Questions Cloud

Starbucks corp in consumer foodservice : Euromonitor International-Analysis - Starbucks Corp in Consumer Foodservice
What is the frequency of the radiation at the maximum : As noted in the chapter, the cosmic microwave background radiation fits the Planck equations for a blackbody at 2.7 K. What is the frequency of the radiation at the maximum
Determine the entropy production for the mixing process : Consider an adiabatic mixing chamber operating at steady state into which steam enters with quality of 0.9. Water enters through a separate inlet at 30 C. At the exit the temperature is 150 C and mass flow rate is 2 kg/s. The pressure in the mixing c..
Find the charge density on each surface of the dielectric : Two parallel plates have equal and opposite charges. When the space between the plates is evacuated, the electric field is E= 3.20×105V/m. find the charge density on each surface of the dielectric
Determine the exit temperature of the air : Air enters the evaporator section of an air-conditioner at 100 kPa, 27 C with a volumetric flow rate of 6 m^3 /min. R-134a enters the evaporator at 120 kPa with a quality of 0.3 and rate of 2 kg/min and it leaves as a saturated vapor at the same pres..
Calculate the magnitude of the charge on each conductor : A cylindrical air capacitor with a length of 13.2m stores an amount of energy equal to 3.20×109J when the potential difference between the two conductors is 4.80V. Calculate the magnitude of the charge on each conductor
Compressor efficiency and the entropy generation : An adiabatic compressor is used to bring saturated water vapor at a pressure of 103 lbf/in^2 up to 1000 lbf/in^2, where the actual exit temperature is 1000 F. Find the compressor efficiency and the entropy generation. Is there an improvement by reduc..
Assuming that the specific heat for the cold fluid : A shell and tube heat exchanger with one shell pass and four tube passes is being analyzed to determine the heat transfer rate and the fluid outlet temperatures for prescribed flow rates and inlet temperatures. The cold fluid has a heat capacity rate..
What does the scale read during the upward acceleration : An elevator undergoes constant upward acceleration, taking it from rest to 12.8m/s in 4.0 s. A 60kg man stands on a scale in the elevator. What does the scale read during the upward acceleration

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A new containment vessel for nuclear waste is being tested

a new containment vessel for nuclear waste is being tested by a group of engineersnbspworking for the u.s. department

  Determine the radius of the orbit and the speed of the

calculate the escape speed from the earth for a 4800 kg spacecraft and determine the kinetic energy it must have at the

  A four-cylinder spark ignition engine has a compression

a four-cylinder spark ignition engine has a compression ratio of 8 and each cylinder has a maximum volume of 0.6l. at

  In a 150 mw steam turbine unit operating on an enhanced

in a 150 mw steam turbine unit operating on an enhanced rankine cycle steam is delivered from the boiler to the high

  What is your reaction use a tolerance limit calculation as

a random sample of 12 shearing pins is taken in a study of the rockwell hardness of the pin head. measurements on the

  Using this data and assuming that the material behaves

the data below give steady state creep rates dedt for a metal alloy as a function of temperature and stress.temp

  At a section down- stream at ground level the pipe diameter

water flows in a circular pipe. at one section the diameter is 0.3 m the static pressure is 260 kpa gage the velocity

  A standardized procedure is expected to produce washers

a standardized procedure is expected to produce washers with very small deviation in their thicknesses. suppose that 10

  Use psychrometric chart to determine latent portion

Use Psychrometric chart to determine Latent portion

  Consider a friction less fluid with a density

Consider a frictionless fluid with a density of 65 lbm/ft3. We describe this fluid as:

  The thermal efficiency of the cycle and the net specific

Determine the thermal efficiency of the cycle and the net specific work. Assume each turbine stage isentropic efficiency to be 99% and assume the FWH is open.

  Determine the factor of safety against brittle fracture

Determine the factor of safety against net section yield in the presence of the crack and determine the factor of safety against brittle fracture for the same conditions.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd