Determine, the exit stagnation temperature of the air

Assignment Help Mechanical Engineering
Reference no: EM131057363

Air enters the first stage of an axial flow compressor at a stagnation temperature of 20°C and at a stagnation pressure of 1.05 bar and leaves the compressor at a stagnation pressure of 11 bar. The total-to-total efficiency of the compressor is 83%. Determine, the exit stagnation temperature of the air and the poly tropic efficiency of the compressor. Assume for air that γ = 1:4.

Reference no: EM131057363

Questions Cloud

Nature of the load connected : An Alternator is found to have its terminal voltage on load condition more than that on no load. What is the nature of the load connected?
Determine the reheat factor based upon stagnation conditions : the overall total-to-total efficiency and total-to-static efficiency assuming the steam enters the condenser with a velocity of 200 m/s;
Center frequency of the filter : The output is taken across the capacitor/coil. The coil winding has a resistance of 20Ω . What is the center frequency of the filter?
Pole single phase induction motor : What will be the direction of rotation of a shaded pole single phase induction motor?
Determine, the exit stagnation temperature of the air : Determine, the exit stagnation temperature of the air and the poly tropic efficiency of the compressor. Assume for air that γ = 1:4.
Non-current limiting fuses : Besides being more expensive. How are current limiting fuse different from non-current limiting fuses?
Create a forecasted profit or loss statement : For the proposed new product or service for your final project, create a Forecasted Profit/Loss Statement for the first year and a Balance Sheet
Transformer and cable overloads : Why is it that fuses and breakers do not prevent transformer and cable overloads? What function do fuses and breakers perform?
What is the overall effectiveness of each screen : what do they show about the ratio by weight of each of the three fractions actually obtained? What is the overall effectiveness of each screen?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Wind is blowing on a 55-gallon drum estimate the wind

wind is blowing on a 55-gallon drum. estimate the wind speed needed to tip the drum over. work in si units. the mass of

  Some alloys use a combination of strain hardening

Some alloys use a combination of strain hardening and precipitation hardening to achieve particularly high strength levels. The usual order of strengthening is solution treatment,quenching, cold working, and finally precipitation heat treatment. Why ..

  Te input to a 12-bit ad converter is vin asin2 omega t

the input to a 12-bit ad converter is vin asin2 omega t 2acos2 omega t and its f 20 khz. find the sampling time

  After passing through the evaporator the refrigerant exits

a heat pump with refrigerant 134a is used maintain a house at 25 degc by absorbing heat from a geothermal water source

  An automobile can accelerate at the rate of 15ms2 and can

an automobile can accelerate at the rate of 1.5ms2 and can decelerate at 7ms2. if driver never exceeds the speed limit

  Determine the maximum velocity leaving the nozzles

Determine the maximum velocity leaving the nozzles and the maximum absolute Mach number in the stage;

  Compute the transit time of an electron

Consider the 2.0micrometer long GaAs device where the E-field is 5kV/cm and Mn*=.067M0. Calculate the transit time of an electron through the device if the mobility is 8000 cm^2V-s.

  An electric heater in the form of a horizontal disk of 57

an electric heater in the form of a horizontal disk of 57 mm diameter is used to heat the bottom of a tank filled with

  What is the temperature and state of the steam in the pipe

a) What is the temperature and state of the steam in the pipe? b) What is the quality of the steam in the pipe?

  Determine the power generation potential

Electric power is to be generated by installing a hydraulic turbine-generator at a site 120m below the free surface of a large water reservoir that can supply water at a rate of 1500 kg/s steadily. Determine the power generation potential.

  The temperatures on the faces of a plane wall 15 cm thick

the temperatures on the faces of a plane wall 15 cm thick are 375 and 85 degrees celsius. the wall is constructed of a

  The boiler pressure is 30 mpa and the cycle has a high

a utility plant runs an ideal rankine cycle with water. the boiler pressure is 3.0 mpa and the cycle has a high

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd