Determine the equivalence ratio

Assignment Help Mechanical Engineering
Reference no: EM13949766

1. The components of the exhaust gas of a spark-ignition engine using a fuel mixture represented as C8H17 have  a dry molar analysis of 8.7% CO2, 8.9% CO, 0.3% O2, 3.7% H2, 0.3% CH4, and 78.1% N2. Determine the equivalence ratio.

2. The combustion of a hydrocarbon fuel, represented as CaHb, results in products with the dry molar analysis 11% CO2, 0.5% CO, 2% CH4, 1.5% H2, 6% O2, and 79% N2. Determine the air-fuel ratio on (a) a molar basis, (b) a mass basis.

3. Decane (C10H22) burns completely in dry air. The air- fuel ratio on a mass basis is 33. Determine the

(a) analysis of the products on a dry molar basis.

(b) percent of theoretical air.

Reference no: EM13949766

Questions Cloud

Kinetic and potential energy : Liquid octane (C8H18) at 778F, 1 atm enters a combustion chamber operating at steady state and burns completely with 50% excess dry air entering at 1208F, 1 atm. The products exit at 10608F, 1 atm. Determine the rate of heat transfer between the c..
Determine the balanced reaction equation : Determine the balanced reaction equation. For the CO and SO2, determine the amount, in kmol per 106 kmol of combustion products (that  is, the  amount in parts per million).
Prepare the income statement for the business : Prepare a 10-column worksheet for the year ended 30 June 2016 - prepare the income statement for the business for the year ended 30 June 2016.
How does kaizen costing differ from standard costing : How much non-value-added cost was eliminated by the end of two quarters? How does kaizen costing differ from standard costing?
Determine the equivalence ratio : The components of the exhaust gas of a spark-ignition engine using a fuel mixture represented as C8H17 have  a dry molar analysis of 8.7% CO2, 8.9% CO, 0.3% O2, 3.7% H2, 0.3% CH4, and 78.1% N2. Determine the equivalence ratio.
How do you explain the difference in these probabilities : P (Z ≥ 1.75) where Z is a standard normal distribution with 10 degrees of freedom. Compare this result to the results obtained in parts (a) and (b). How do you explain the difference in these probabilities?
Determine the percent of theoretical air : 1. Hydrogen (H2) enters a combustion chamber with a mass flow rate of 5 lb/h and burns with air entering at 858F, 1 atm with a volumetric flow rate of 75 ft3/min. Determine the percent of theoretical air  used.
Describe briefly any workflow database that you know of. : What types of tasks would benefit from databases utilizing workflow technology?
Determine the dew point temperature of the products : 1. Acetylene (C2H2) enters a torch and burns completely with 110% of theoretical air entering at 748F, 1 atm, 50% relative humidity. Obtain the balanced reaction equation, and determine the dew point temperature of the products, in 8F, at 1  atm...

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  R-410a flows inside the tubes and evaporates at a constant

the cooling coil of a small air-conditioning system is to be designed for a heat-transfer rate of 48000 btuhr from air

  Etermine the principal stresses and maximum shearing stress

four forces are applied to a W200x35.9 rolled beam as shown. determine the principal stresses and maximum shearing stress at point a.

  Oil has a specific gravity

Oil flows at a rate of 12gpm from a vented tank (pressure at point 1 is zero) through 1 inch inner diameter pipes and elbows, and through a pump and motor as shown. The pump adds HHPp= 3hp to and the motor extracts HHPm= 1hp from the fluid power.

  Difference between stagnation pressure and static pressure

A Pitot-static probe is sued to determine the airspeed of an airplane that is flying at an altitude of 6000 m. If the stagnation pressure is 4.8540x104 N/m2 recorded by a gage that measures the difference between the stagnation pressure and the stati..

  What is the value of heat transfer coefficient at this

the temperature profile at a location in water flowing over a flat surface is experimentally measure to be tdegc

  What is the specific heat of air in us customary units

what is the specific heat of air in US customary units given that its value in SI units is approximately 1 kN.m/kg.K?

  Assuming one-dimensional heat transfer and disregarding

a 4-m high and 6-m wide wall consists of a long 18-cm x 30-cm cross section of horizontal bricks k 0.72 wm middotdegc

  Air enters the compressor section of a turbojet engine at

air enters the compressor section of a turbojet engine at 15 c and 0.1 mpa at a rate of 100 m3min. the air leaves at

  What is the quality of the steam in its initial state

A saturated mixture of water at 1,100kPa is throttled (in a throttling process) to a temperature of 105 degrees C and a pressure of 100kPa. What is the quality of the steam in its initial state?

  Calculate the unit cell edge length

Calculate the unit cell edge length  for an 80 wt% Ag-20 wt% Pd alloy. All of the palladium is in solid solution, the crystal structure for this alloy is FCC, and the room temperature density of Pd is 12.02 g/cm3.

  The piston will be moved slowly and reversibly until 25

one kilogram of saturated liquid methane at 160 k is placed in an adiabatic piston-and-cylinder device and the piston

  Engine room cranea new vessel is being designed to provide

engine room cranea new vessel is being designed to provide a container service between two atlantic ports. the owner

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd