Determine the entropy production rate

Assignment Help Mechanical Engineering
Reference no: EM131293845

Determine the entropy production rate as 0.0500 kg/s of air flows through a vortex tube from an inlet pressure of 1.00 MPa.

Both hot and cold side exit pressures are 101.3 kPa, and the hot side temperature is 50.0°C while the cold side temperature is -40.0°C.

Two thirds of the inlet mass flow rate passes through the hot side exit.

Assume constant, specific heat, ideal gas behavior and neglect any changes in kinetic and potential energy.

Reference no: EM131293845

Questions Cloud

Many forms of communication : Over the past 4 weeks, we have discussed many forms of communication.  Last week, we specifically looked at visuals and the best way to make use of them.  We are, once again, going to focus this information on a specific area...Marketing.  Followi..
Community health strategy for dealing with intentional : Question 1: Select one of the age groups discussed in this unit (adolescents, adult, or elderly) and create a community health strategy for dealing with intentional and unintentional injuries (motor vehicle accidents, suicide, or violence),
How would you record the transaction : IF 2012 TAXABLE INCOME FOR JAR, INC.WAS $85,000. AND IF 2013 TAXABLE LOSS IS $35,000 TAX RATE 40% WOULD IT BE POSSIBLE TO UTILIZE THE TAXABLE LOSS FROM 2013 TO THE CORPORATION'S BENEFIT. IF SO, HOW WOULD YOU DO IT AND HOW WOULD YOU RECORD THE TRANSAC..
Executing a new performance appraisal system : Why would training be a critical component to executing a new performance appraisal system? What value would training bring to the process? Who should be given training within Matrix, and why?
Determine the entropy production rate : Determine the entropy production rate as 0.0500 kg/s of air flows through a vortex tube from an inlet pressure of 1.00 MPa.
Explain how to find the lengths of the legs of the triangle : The hypotenuse of a 30 degree, -60 degree, -90 degree triangle is 24.2-ft. Explain how to find the lengths of the legs of the triangle.
Secondary human factors contributions to the accident : Develop a case analysis on this topic: Select a commercial aviation accident that was concluded to have resulted from pilot error. Determine the primary and any secondary human factors contributions to the accident.
Are supplements good for you : Vitamin and mineral supplements have been in the news a lot lately. There's conflicting information out there: Are supplements good for you? Are they necessary? Should everyone be taking them?
Determine steady state eprd of an insulated steam turbine : Determine the steady state EPRD of an insulated steam turbine that has a total mass of 2000. kg, takes in steam at 3.50 MPa, 400.°C at a rate of 2.00 kg/s and exhausts it at 5.00 kPa, 90.0% quality.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd