Determine the entropy generation kjkg-k for the compressor

Assignment Help Mechanical Engineering
Reference no: EM13632799

Saturated liquid water is compressed from 100 kPa (State 1) to 2.5 MPa (State 2) in an adiabatic pump having 85% isentropic efficiency. Calculate the specific work (kJ/kg) required for the compression of liquid water. Determine the entropy generation (kJ/kg-K) for the pump. Saturated water vapor is compressed from 100 kPa (State 3) to 2.5 MPa (State 4) in an adiabatic compressor having 85% isentropic efficiency. Calculate the specific work (kJ/kg) required for the compression of water vapor. Determine the entropy generation (kJ/kg-K) for the compressor. Comment on the relative magnitudes of the specific work and entropy generation for the pump and the compressor.

Reference no: EM13632799

Questions Cloud

Find by dimensional analysis how the period t of a : find by dimensional analysis how the period t of a satellite orbiting a planet of mass m depends upon the gravitational
If other factors remain constant the larger the sample is : if other factors remain constant the larger the sample is the more likely you are to obtain a significant value for the
In what direction and at what speed does the wreckage move : two automobiles each of mass 1000kg are moving at the same speed 20 ms when they collide and stick together in what
Why is it preferable to use nuclear binding energy per : why is it preferable to use nuclear binding energy per nucleon for a comparison of the stabilities of different
Determine the entropy generation kjkg-k for the compressor : saturated liquid water is compressed from 100 kpa state 1 to 2.5 mpa state 2 in an adiabatic pump having 85 isentropic
Methabe reacts withoxygen in the air to produce carbon : methabe reacts withoxygen in the air to produce carbon dioxide and water. ammoniareacts with oxygen in the air to
A convex lens is held over a piece of paper outdoors on a : a convex lens is held over a piece of paper outdoors on a sunny day. when the paper is held 21 below the lens the
This cycle is operated at 80 kpa and 20oc at the beginning : an air-standard dual cycle has a compression ratio of 14 and a cut-off ratio of 1.2. the pressure ratio during the
Scl2 state the molecular polarity in a 3d sketch of : scl2 state the molecular polarity in a 3d sketch of youmolecule and lable the dipole moment of each bond state

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the time taken for the product to freeze if it is

a fruit juice containing 30 solids of molecular weight 100 g was placed in a tray length 100 cm height 90 cm width 8

  Draw the t-s diagram

Draw the T-s diagram (hint: it would help to begin with a schematic of the cycle) and.

  A 48-tonne ferry strikes a dock at 3 kmh what average

a 48-tonne ferry strikes a dock at 3 kmh. what average force does it exert on a dock if it is brought to rest over a

  An electric motor draws a current of 10 amp with a voltage

an electric motor draws a current of 10 amp with a voltage of 110v. the output shaft develops a torque of 10.2 n-m and

  What is the probability that more than eleven loads occur

an article suggests that a poisson process can be used to represent the occurrence of structural loads over time.

  What is the most cost-effective way of acquiring the parts

Your engineering firm decides to build a prototype, and needs screw and nut fasteners as well as resistors and LEDs. There are machinists and electronics technicians available for in-house production. What is the most cost-effective way of acquiri..

  Derive a relationship between partial molar excess

derive a relationship between partial molar excess enthalpy activity coefficient of species i and temperature. assume

  Consider a low speed one-circuit wind tunnel with an inlet

consider a low speed one-circuit wind tunnel with an inlet to throat ratio of 12. the pressure difference between the

  Define a jack-screw has a handle inches long

A jack-screw has a handle 35 inches long and a pitch of 7/32 inches. If a pull of 15 lbs. is required at the end of the handle to lift a 3,000 lbs.

  A hollow steel shaft 6 ft long has an outer diameter of 25

a hollow steel shaft 6 ft long has an outer diameter of 2.5 in. and an inner diameter of 1.5 in. the shaft is

  Bron is diffused into highly pure germanium at 1000oc q

boron is diffused into highly pure germanium at 1000oc q 105 kcalmol do 1.1 x 10 m2sec. a steady surface

  The exhaust temperature of a carnot heat engine is 305degc

the exhaust temperature of a carnot heat engine is 305degc. what is the intake temperature if the efficiency of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd