Determine the entropy generated for the process

Assignment Help Electrical Engineering
Reference no: EM13228213

An adiabatic piston cylinder contains 1 kg of R-134a. Initially the conditions inside the piston are 200 kPa and 0 degrees C. An electric heater inside the device runs with constant voltage of 110 V and a constant 0.1A of current for one hour. If the system is then compressed with an additional 18.3 kJ of energy until the final pressure inside the device reaches 500 kPa, determine the entropy generated for this process.

Reference no: EM13228213

Questions Cloud

Slow steaming as part of a supply chain strategy : How should a shipper decide whether or not to use slow steaming as part of a supply chain strategy?
Compare and contrast two of the rfc types identified : To familiarize yourself with the Internet Standards, search the Internet for the IETF RFC website. Using the information you find on this site, answer the following questions: Identify four types of Internet standards.
Explain what fraction of the radioactivity will appear : what fraction of the radioactivity will appear as CO2 during the first 2 turns of the TCA cycle? Draw the structure of OAA and indicate its labeling pattern after the second turn of the TCA cycle.
Explain the metabolism of glutamic acid in e coli : You are investigating the metabolism of glutamic acid in E coli, which enters the TCA cycle as a-Ketoglutarate following an initial transamination reaction.
Determine the entropy generated for the process : An adiabatic piston cylinder contains 1 kg of R-134a. Initially the conditions inside the piston are 200 kPa and 0 degrees C. An electric heater inside the device runs with constant voltage of 110 V and a constant 0.1A of current for one hour
What analysis should the manufacturer decide : A more reliable trucking firm promises delivery exactly in six days, but for a 5 % higher cost. What analysis should the manufacturer decide whether or not to switch?
Explain the citrate synthase reaction : If all the pyruvate is metabolized by the glyoxylate bypass (assume that 50% of the pyruvate enters in the citrate synthase reaction and 50% during the bypass), what would be the labeling pattern and its distribution in the oxaloacetate?
Would such a strategy save cost : A consultant recommends that the retailer should set up a consolidation warehouse in Shanghai that collects all the products from suppliers and pays them, and organize ocean shipping to the US. Would such a strategy save cost ? Explain
State the absorbance of light increases as the concentration : Provide a molecular-level explanation for why the absorbance of light increases as the concentration of dissolved food dye in a solution increases.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How to evaluate power dissipated in the components

how to evaluate power dissipated in the components of an RLC series circuit by using matlab software?

  Determine zero-input response

Determine zero-input response of (D2+4D+40)y(t)=(D+2)x(t) with initial condition y0(0)=2 & dy0(0)/dt=16.78.

  Calculate the maximum power

Calculate the maximum power that can be sent through an a=2cm , b=1cm air-filled waveguide at 12 GHz such that dielectric breakdown does not occur. Assume that the dielectric strength of air at atmospheric pressure is 3x10^6 [V/m]

  Determine the concentration of donor impurity atoms

A silicon sample at T = 300 K contains an acceptor impurity concentration of \(N_{A}\) = 1016 cm-3. Determine the concentration of donor impurity atoms that must be added so that the silicon is n-type and the Fermi energy is 0.20 eV

  Calculate the reluctance of the magnetic circuit

A ‘c-core' inductor has a total air-gap length of 3 mm and a cross-sectional area of 100 cm2. Two coils are wound on the core - one of 500-turns and another of 250-turns. Assuming the iron reluctance, fringing flux and leakage flux to be negligibl..

  Explain the significance of these intersections

construct a vertical line on your I versus V graph at the point V=5V. this line will intersect each of the sloping lines at two separate points. explain the significance of these intersections.

  Calculate necessary excitation voltage n input complex power

A 150 MVA, 24 kV, 123% three-phase synchronous generator carries the rated load at a power factor 0.83 (lagging). Calculate the necessary excitation voltage and input complex power.

  Give a narritve for a cruise control system of a car

Give a narritve for a cruise control system of a car. Include all relevant inputs and outputs. Design a flowchart and ladder diagram. Every element on the ladder diagram must be labelled and described.

  Describe the functionality of the above dfsm

Describe the functionality of the above DFSM using transition tables. Consider that the system starts always from state B. What happens if the system will start from another state - say A?

  Define a block error detecting code has a minimum distance

A block error detecting code has a minimum distance of three. How many errors can this code detect and how many can it correct

  How many quantization bits must be used to satisfy

An analog signal ranging between 0 and 1 V must be quantized. The midrange quantization errors must be no greater than 0.1V. How many quantization bits must be used to satisfy this requirement

  Estimate the worst case variation in film thickness

A wafer 100mm in diameter is mounted in an electron-beam evaporation system in which spherical radius is 40cm. Estimate the worst case variation in film thickness between the center and edges of the wafer for an evaporated aluminium 1micro meter t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd