Determine the entropy change of nitrogen during this process

Assignment Help Mechanical Engineering
Reference no: EM13718191

A piston-cylinder device contains 1.101 kg of nitrogen gas at 120 kPa and 27 degrees C. The gas is now compressed slowly in a poly tropic process which PV^(1.38) = constant. The process ends when the volume is reduced by one-half. Determine the entropy change of nitrogen during this process.

Change in entropy _________ kJ/K (round to four decimal places)

Reference no: EM13718191

Questions Cloud

Estimate what is the terminal velocity of the bar : Two conducting rails 31.5 cm apart rest on a 4.97° ramp. They are joined at the bottom by a 0.750 ohm resistor, What is the terminal (steady) velocity of the bar as it slides frictionlessly down the rails
Adiabatic flame temperature with increasing combustion air : Propane gas (C3H8) at 25oC, 1 atm enters an insulated reactor operating at steady state and burns completely with air entering at 25oC, 1 atm. Plot the adiabatic flame temperature versus percent of theoretical air ranging from 100 to 400%.
How much elastic potential energy was stored in the spring : A 0.39-kg cart and a 0.13-kg cart are held together with a compressed spring between them. How much elastic potential energy was stored in the spring before the release
Determine how high will the block rise into the air : A gun fires a bullet vertically into a 1.40-kg block of wood at rest on a thin horizontal sheet. how high will the block rise into the air after the bullet becomes embedded in it
Determine the entropy change of nitrogen during this process : A piston-cylinder device contains 1.101 kg of nitrogen gas at 120 kPa and 27 degrees C. The gas is now compressed slowly in a poly tropic process which PV^(1.38) = constant. The process ends when the volume is reduced by one-half. Determine the entro..
How fast is the flowerpot moving in two seconds : A flowerpot falls from a windowsill 25 m above a sidewalk. How fast is the flowerpot moving in 2 seconds
Examine specific ways and events : Discussion, examine specific ways, events, characterizations, places, times, imagery, symbolism, etc., unfolds the story of the myth or folktale or satire.
How many different customers have ordered products : How many different customers have ordered products in each category? Two columns, categoryname and count of distinct customers. Make sure to include EVERY category.
Estimate what will be their speeds after the collision : Two billiard balls of equal mass undergo a perfectly elastic head-on collision. what will be their speeds after the collision

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd