Determine the distance from the left hand end of the beam

Assignment Help Civil Engineering
Reference no: EM13299815

Draw the shear force and bending moment diagrams for the beam, making sure to include values for the maximum positive and negative bending moments and their locations. Also determine the distance from the left hand end of the beam to the point where the bending moment is zero (ie the point of contraflexure).

Reference no: EM13299815

Questions Cloud

Explain the concentration of the first ion that precipitates : A solution contains .10 M iodide ion, I- and 0.10 M carbonate ion, CO32-.... a. If solid Pb(NO3)2 is slowly added to the solution which salt will precipitate first, PbI2 or PbCO3? What will the concentration of the first ion that precipitates when..
Calculate the maximum design load on a hollow aisi : Calculate the (maximum) design load on a hollow AISI 1020 steel shaft with an outside diameter of 2.5 inches and an inside diameter of 2 inches. Assume a safety factor of 2.
Calculate the mass emissions rate of ash into the atmosphere : The coal has an ash content of 12% by mass. Forty percent of the ash falls out the bottom of the furnace. The rest of the ash is carried out of the furnace with the hot gases into an electrostatic precipitator (ESP).
What fraction of the original light is absorbed by analyzer : The transmission axis of the analyzer makes an angle of 32.0° with the axis of the polarizer. What fraction of the original light is absorbed by the analyzer
Determine the distance from the left hand end of the beam : Draw the shear force and bending moment diagrams for the beam, making sure to include values for the maximum positive and negative bending moments and their locations. Also determine the distance from the left hand end of the beam to the point whe..
What is the frequency of the beacon observed on spaceship : A spaceship is approaching a space station at a speed of 2.55 multiply.gif 105 m/s. What is the frequency of the beacon observed on the spaceship
Calculate ultimate bod where discharge and river meet : Wastewater from a paper mill contains ultimate BOD of 200ppm and DO of 3ppm, water is discharged at a rate of 100,000 gallons per day into a river, the river has a flow of 1 million gallons per day with no BOD
Revenue-enhancing measure : Beachside City enacts an ordinance that bans the distribution of all printed materials on city streets. Carl opposes the city’s latest “revenue-enhancing” measure and wants to protest by distributing handbills. In his suit against the city, a cour..
Find the power of the starlight the earth intercepts : Consider a bright star in our night sky. Assume its distance from Earth is 45.9 light-years (ly) and its power output is 4.00 multiply.gif 1028 W, Find the power of the starlight the Earth intercepts

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the dimensions of an acceptable box of a largest area

a delivery company accepts only rectangular boxes the sum of whose length and girth (perimeter of a cross section) are equal to 108cm. find the dimensions of an acceptable box of a largest area.

  What is the corrected measurement

A measurement was recorded as 171.278 m with a 30-m tape that was only 29.996 m under standard conditions. What is the corrected measurement?

  Find summer values for oxygen demand and oxygen tranfer

A fine-bubble aeration basin has a flow of 21.5 mgd, an influent BOD of 180 mg/l, 31 mg/l of mmonia, and effluent of 10 mg/l. During the winter, the wastewater temperature of 14.8 degrees C does not nitrify.

  Draw p-v dia for pure component and label appropriate point

Draw a P-V diagram for pure component and label appropriate points such as superheated region, isothermal line, etc.

  Determine the manning coefficient of channel roughness

A discharge of 2,200 ft^3/sec flows in a trapezoidal channel at a normal depth of 8.0 ft. The channel has a slope of 0.01, a 12-ft bottom width, and side slopes of 1:1 (H:V). Determine the manning coefficient of channel roughness

  Using pestan model for a project

I want to use PESTAN model for a project, can you please tell me any real scenario with available data on which I can formulate a project preferably related to oklahoma.

  Estimate the change in pressure over 100 m of pipeline

Water at 20 degrees flows at a velocity of (V =) 2 m/s in a (D =) 250-mm diameter horizontal ductile iron pipe. Estimate the friction factor f in the pipe, and state whether the pipe is hydraulically smooth or rough.

  Determine the velocity in horizontal x-y plane

A particle with a mass of 0.5 kg has a velocity of 10 m/s in the x-direction at time t = 0. Forces F1 and F2 act on the particle, and their magnitudes change with time according to the graphical force-time history shown.

  How much does the aggregate in the wheelbarrow weight

you fill a 2-cubic foot wheelbarrow to the top with aggregate. if the specific gravity of the aggregate is 2.548 and 18% of the aggregate is void spaces, how much does the aggregate in the wheelbarrow weight?

  Determine reduced live load supported by exterior column

A 45-cm-thick, 300-cm-high lightweight concrete masonry unit wall lies on a 20-cm-thick lightweight plain concrete slab. The 20-cm wide slab is supported by a reinforced concrete beam, which is placed on top of two columns (simply supported beam).

  How many acres are within the enclosed by the fence

A contractor has installed a silt fence around an area that is semi-circular and level to prevent soil from the construction site entering nearby streams. The diameter of the semi-circle is 1000 feet.

  Find e for tendon to be concordant

Find e1, e2, e3 for tendon to be concordant - find deflection at those location

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd