Determine the diameters of each exit ducts in meters

Assignment Help Electrical Engineering
Reference no: EM13281253

Steam at 160 bar and 480oC enters a turbine operating at steady state with a volumetric flow rate of 800 m3/min. Eighteen percent of the entering mass flow exits at 5 bar, 240oC, with a velocity of 25 m/s. The rest exist at another location with a pressure of 0.06 bar, quality 94% and velocity 400 m/s. Determine the diameters of each exit ducts in m.

Reference no: EM13281253

Questions Cloud

Study scenario in the area of computer system perfor­mance : Develop a study scenario in the area of computer system perfor­mance. Describe specifically and in detail how you would apply each step of the scientific method to carry-out the study.
Explain the combustion reaction of propane : The combustion reaction of propane, C3H8, in the presence of molecular oxygen, O2, is an equilibrium reaction that produces carbon dioxide and water. Express the equilibrium constant for this reaction.
Determine heat transfer in kj using constant specific heat : A piston cylinder assembly contains 1 kg of nitrogen gas. The gas expands from an initial state where T1 = 700 K and P1 = 5 bar to a final state where P2 = 2 bar. During the process the pressure and the specific volume are related by Pv1.3 = const..
Find out the element of lowest atomic number : Determine the element of lowest atomic number that contains a complete d subshell in the ground state. element symbol
Determine the diameters of each exit ducts in meters : Steam at 160 bar and 480oC enters a turbine operating at steady state with a volumetric flow rate of 800 m3/min. Eighteen percent of the entering mass flow exits at 5 bar, 240oC, with a velocity of 25 m/s.
Determine the final volume assuming ideal gas behavior : A gas is confined to one side of a rigid insulated container divided by a partition. The other side is initially evacuated. The following is known for the initial state of the gas: P1 = 3 bar, T1 = 380 K and V1 = 0.025 m3.
Explain the thermal insulation around the turbine : If a breakdown of the thermal insulation around the turbine allows a heat loss of 60 kJ per kg of stream, and the exiting steam is at 150oC and 0.3 MPa, what will be the power developed by the turbine if the inlet steam conditions and flow rate ar..
What is the yield or return on this preferred stock : This preferred stock is currently selling for $56.46 per share. What is the yield or return (r) on this preferred stock?
Calculate average value of current i during life of battery : A standard D cell flashlight battery is connected to a load of 3 ohms. After 6 hr of intermittent use the load voltage drops from an initial 1.5 V to a final useful voltage of 0.9 V. (a) Calculate the internal resistance of the battery at the load ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is role of miller in high frequency amplifier design

1. What is Miller capacitance What is its role in High frequency amplifier design Label all the involved variables in the Figure below and derive an expression for the Miller effect capacitances (input and output).

  What is the percentage of distortion level at the frequency

The sampling frequency in a DSP system is fs = 8khz kHz. A hold circuit is used after the DAC device. What is the percentage of distortion level at the frequency f= 3.4 kHz

  Find ?v if the charge is distributed uniformly over volume

A cube with an edge of length 2 mm is charged to -1.2 C. Find: a)ρv , if the charge is distributed uniformly over its volume ; b) ρs , if the charge is distributed uniformly on its surface; c)ρL , if the charge is distributed uniformly on the edges o..

  How does the amount of electrons-charge change

clarify if this is correct. On the charge profile graph, I do not understand how the charge is fluctuating up and down to make a current since current is the change in charge over time. How does the amount of electrons/charge change within the cir..

  How to design a simple unipolar drive circuit

Design a simple unipolar drive circuit such that the electrical time constant is 2 msec at phase turn-on and 1 msec at turnoff. The stepping rate is 300 steps per second. A three-phase variable-reluctance stepper motor has parameters.

  What will be the peak current through the switch at instant

A permanent magnet DC motor with a 10 ohms armature is stopped by dynamic braking. at operating speed, the counter EMF in the motor armature is 15 volts. What will be the peak current through the switch at the instant it shorts out the motor

  What is the amount of heat added until the piston just lifts

A piston-cylinder arrangement whose piston is resting on a set of stops contains 0.5 kg of helium gas at 100 kpa and 25oC. the mass of the piston is such that a pressure of 500 kPa will just life it off the stops.

  Determine the phase angle between the inverter

Determine the phase angle between the inverter fundamental voltage,VC1, and grid side voltage such that the power delivered to the grid is 10 kW and the fundamental current leads VS by 150°. Calculate the reactive power to the grid and draw the ph..

  What is the allowable signal swing at the collector

Using a 3-V power supply, design a version of the circuit of fig 6.62 from the book. to provide a dc emitter current of 0.5 mA and to allow a +-1-V signal swing at the collector. The BJT has a nominal B=100. Use standard 5 % resistor values

  Calculate the armature voltage required on the motor

A separately excited dc motor turns at 1200rpm when the armature is connected to a 115V source. Calculate the armature voltage required so that the motor runs at 1500rpm.

  Explain how are timer instructions reset

1. What is the difference between On-delay and Off-delay timer instructions 2. How are timer instructions reset What happens when an On-delay timer reaches its preset delay time

  Find the vector form of pq and the lenght of vector pq

Two points with the coordinates P(2, 5, -1) and Q (3, 0, 4) exists in space. Find the vector form of PQ, the lenght of vector PQ, and the unit vector form of PQ

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd