Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 200 ft length of solid copper wire is measured to have a resistance of .500 Ohms.
a. Determine the cross sectional area of the wire in both square mils and in circular mils.
b. Determine the diameter of the wire in mils and in inches.
Here on Cramster it shows a step where
500 ohms = [(10.36)(CM-oms/ft)(200ft) / A
Where is the 10.36 coming from? That should be Ohm Meters, but how do we know what that is? I don't see where or how its been stated in a wire table or in the problem itself. Where is the 10.36 coming from?
ManchesterEncodingFSM the clock (Clk_H) will need to run at a speed that is twice as fast as the clock that defines the boundaries of the RawSerialIn_H serial data bit cell this will allow the FSM to resolve or discriminate the middle of each raw ..
A core-type transformer rated at 37.5 kVA, 2400/480 V, and 60 Hz has a core whose mean length is 1.07 m and whose cross-sectional area is 95 cm^2. The application of rated voltage causes a magnetic field intensity of 352 A-t/m (rms)
The dielectric materials used in real capacitors are not perfect insulators. A resistance called a leakage resistance in parallel with the capacitance can model this imperfection. A 150-F capacitor is initially charged to 100 V.
Design an AC source system that can be used to power 120 Vrms, 240 Vrms, and 208 Vrms single phase devices depending upon the particular connection terminals. The system should have no individual sources with voltages larger than 120 Vrms.
A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-V rms sinusoidal source. Calculate (a) the average and reactive powers delivered to the load, (b) the peak current, and (c) the load impedance.
Let X be a random variable uniformly distributed on [-2,2]. Define the random variable y=g(x), where g(x) { x+1 : x >= 0 { x-1 : x
Design an amplifier using a JFET and a 20V power supply. Calculate the required resistor and capacitor values for the circuit, assuming a minimum frequency of 10 Hz.
If blood flows at a rate of 5 L/min for 3.5 minutes and then 4.5 L/min for 2 minutes, calculate the amount of blood that has moved through the body over the whole time period.
Determine the minimun number of 20 Acircuits required to supply the general lighting load in a residence of 1750 sq ft. in terms of good design practice, what is the max of receptacles allowed on a dedicated small appliance branch circuit
A collector modulated transmitter has a supply voltage of 48 V and an average collector current of 600 mA. What is the input power to the transmitter. How much modulating signal power is needed to produce 100 percent modulation.
Given a sawtooth signal with fundamental frequency = 20 KHz as the input signal going into an ideal Highpass Filter with cutoff frequency fc = 60 KHz, what frequency components will be obtained at the output
What is the smallest frequency that can be used to sample each of the following continuous-time signals such that the signal can be recovered from the discrete samples (a) \(x(t)=1+cos(2000\pi t)+cos(4000\pi t)\)
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd