Determine the curve elements-pc and pt stations

Assignment Help Civil Engineering
Reference no: EM13323539

A horizontal curve on a two-lane highway is designed with a degree of curvature of 7 degree and a 50mph design speed. The coefficient of side friction for the design speed is 0.14. Deflection angle is 90 degree. Its PI station is 20+00.00. An existing building is 10 ft from the inside edge of the inside lane.
Determine :
1) Curve elements, PC and PT stations
2) Design a superelevation rate.
3) Does the building need to be relocated in order to provide sufficient stopping sight distance?

Reference no: EM13323539

Questions Cloud

Find the net charge of all these electrons : Water has a mass per mole of 18.0 g/mol, and each water molecule (H2O) has 10 electrons. What is the net charge of all these electrons
Explain the approximate molecular weight of the gas : A sample of gas is collected over water at c and mm Hg. The collected gas occupies 130 mL. The vapor pressure of water at 23.5 c is 21.7 mm Hg. The approximate molecular weight of this gas
Calculate the concentration of so2 in the exhaust gases : For an SO2 emission rate of 22,000 kg/day and an exhaust gas flow rate of 5.0 million m^3/hour(after the scrubber) measured at 150 C and 1atm pressure, calculate the concentration of SO2 in the exhaust gases(ppm).
Explain what substance is produced at the anode : What substance is produced at the anode during the electrolysis of a mixture of molten calcium bromide, CaBr2(l), and molten magnesium iodide,MgI2(l)
Determine the curve elements-pc and pt stations : A horizontal curve on a two-lane highway is designed with a degree of curvature of 7 degree and a 50mph design speed. The coefficient of side friction for the design speed is 0.14. Deflection angle is 90 degree.
Explain the vapor pressure of h2 and vapor pressure of water : Mg + 2HCl --> MgCl2 + H2 For a mass of 0.013 g Mg and 5.0 mL of 1.00 M HCl, in a flask with V = 140.612 mL at 23.5?C. Calculate the vapor pressure of H2 and vapor pressure of water.
Determine the void ratio and specific gravity of the soil : A saturated soil has a unit weight of 120 pcf and a water content of 32.5%. Determine the void ratio and specific gravity of the soil.
Evaluate the initial and final pressure atm : Mg + 2HCl --> MgCl2 + H2 For a mass of 0.013 g Mg and 5.0 mL of 1.00 M HCl, in a flask with V = 140.612 mL at 23.5?C. Calculate the initial and final pressure (atm).
Determine all possible total orders of transactions : Let objects x and y be stored at site 1, and objects z and w be stored at site 2. Determine, for each of the following executions, whether the execution is serializable or not.

Reviews

Write a Review

Civil Engineering Questions & Answers

  How large a sample must we take in order to be confident

how large a sample must we take in order to be a) 95% b) 90% c) 99 d) 99.73% confident that the error in the estimated mean lifetime will not exceed 20 hours.

  Calculate the bulk density and water content of peat ratio

A 150 mm diameter by 300 mm long sample taken from the peat deposit was weighed and found to have a total mass of 5036 g and after oven-drying a dry mass of 387,4 g.

  Determine the design a typical joint 50mm wide

A floor is to be supported on hardwood timber joists that are spaced at 0.5m centres and span 5.0m. The joists support flooring 20mm thick and an applied live load of 2kN/m2 Design a typical joint 50mm wide

  Calculating the principle of shoring system

How to calculate the principle of shoring system in formwork analysis when the secondly floor upper has been poured?

  Determine the allowable value of the tensile load p

A steel bar serving as a vertical hanger to support heavy machinery in a factory is attached to a support by the bolted connection. The main part of the hanger has a rectangular cross section with width b1 = 1.5 in. and thickness t = 0.5 in.

  Find final temperature-specific work and specific heat

a piston/cylinder contains liquid water at 2 degrees Celcius, with a freely moving piston maintains a pressure of 200 kPa on the water. Heat transfers to the liquid water until the piston/cylinder contains only saturated vapor.

  Determine max hoop stresses on inside fibers of rifle barrel

Determine the maximum hoop stresses on the inside fibers of a rifle barrel which is 3 feet long with an O.D. = 3.0" and an I.D. = 1.0". The internal pressure = 10,000 psi. Use the F.E. reference manual for determining these stresses.

  Geophysical techniques using electromagnetic induction

Describe the application of geophysical techniques using electromagnetic induction as a tool for sustainable soil and water management of agricultural fields in the humid tropic Caribbean 300 word limit.

  Determine the x-y and z components of reaction at the pin

The member is supported by a pin at A aand a cable BC. If the load at AD is 300 lb, determine the x,y,z components of reaction at the pin A and the tension in cable b c

  Find hp per foot of cutting edge ratio for all 4-conditions

The Caterpillar D6R Series 3 and D8R tractors are rated, respectively, at flywheel horsepowers (fwhp) 0f 185 and 305. The "A," "S," and "SU" blade widths (length) for the D6R are S, 16 ft, 9 in.; A, 17 ft, 1 in

  Estimate depth change in lake in feet during a 1-year period

The evaporation rate from the surface of a 3650-acre lake is 100 acre-ft/day. Estimate the depth change in the lake in feet during a 1-year period if the net inflow to the lake is 25 cfs. Is the depth increasing or decreasing

  Determine the initial specific discharge under the gate

Write out the continuity and momentum equations that govern the surge travelling downstream. (Note: assume that the surge velocity exceeds the water velocity)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd