Determine the current i2 using branch current analysis

Assignment Help Electrical Engineering
Reference no: EM131203813

For the networks of given figure, determine the current I2 using branch-current analysis, and then find the voltage Vab.

70_Network.jpg

Reference no: EM131203813

Questions Cloud

Discuss the liability of your measurement strategy : Identify a concept (e.g. attitudes towards elderly, marital satisfaction, delinquency, social class) that receives attention in this area and that interests you. Describe how you might conceptualize this concept.
State the null hypothesis for the effect of guided imagery : State the null hypothesis for the effect of guided imagery on pain scores for the subjects in the treatment group at 12 weeks. Should this null hypothesis be accepted or rejected? Provide a rationale for your answer.
Find the current through each resistor for the networks : Using branch-current analysis, find the current through each resistor for the networks of given figure. - The resistors are all standard values.
Calculate the standard error of a regression equation : Calculate the standard error of a regression equation if the sum of squared errors of the observations is 625 and the degrees of freedom in the regression is 25.
Determine the current i2 using branch current analysis : For the networks of given figure, determine the current I2 using branch-current analysis, and then find the voltage Vab.
What is the speed regulation of this motor : A three-phase 60-Hz two-pole induction motor runs at a no-load speed of 3580 r/min and a full-load speed of 3440 r/min. Calculate the slip and the electrical frequency of the rotor at no-load and full-load conditions. What is the speed regulation ..
Cost of goods sold using the lifo and fifo methods : Surplus, Inc. uses a periodic inventory system and the had the following activity for 2007: Calculate the ending inventory and cost of goods sold using the LIFO and FIFO methods.
Week on the horizontal axis : Considering Pat and Kris jointly as one "nation," draw the PPF for this nation, with pizzas per week on the vertical axis and gallons of beer per week on the horizontal axis.
Write equations necessary to solve for the branch currents : Write the equations necessary to solve for the branch currents. - By substitution of Kirchhoff's current law, reduce the set to three equations.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine what impedance does a driving generator see

A one quarter wavelength piece of 75 ohm microstrip line has a capacity load of Xc = 22 ohms. What impedance does a driving generator see

  What is average transmitted power and modulation index

What is the bandwidth required so that the modulated signal contains atheist 90% of the power of the unmodulated carrier. A carrier signal c(t) = 10 cos(2pifct) is modulated using a message signal m(t) cos(20pit). The modulation is FM, with kf = 50.

  Describe the vertical chain for production of motion picture

Describe the vertical chain for the production of motion pictures. Describe the extent of vertical integration of the steps in this chain.

  Find the numeric solution to the conduction angle equation

Use a Spread Sheet or MATLAB or write a computer program to find the numeric solution to the conduction angle equation for a 60hz Half-Wave rectifier circuit that uses a filter capacitance of 100,000µf. The circuit is designed to provide 5v and 5a..

  Design logic circuit to control electrical power to engine

Design a logic circuit to control electrical power to the engine ignition of a speed boat. Logic output I is to becomehigh if ignition power is to be applied and is to remain lowotherwise. Gasoline fumes in the engine compartment present aserious ..

  How much work is done upon the crate by friction

A 9.2 kg crate is pulled up an incline with initial speed of 1.2 m/s A pulling force of 105N is applied parallel to surface of incline which is at angle of 21.8 degrees to horizontal The coefficient of kinetic friction is .32 and crate is pulled d..

  What are the advantages of a current controlled device

What are the advantages of a current controlled device over a voltage controlled device , and advantages of 4-20mA loop over a closed loop voltage

  Determine the minimum numbber of bit required for each word

1) Determine the number of possible PCM values that can be encoded for (a) 6 bits and (b) 10 bits. 2)it is desired to represent an analog signal in no less than 500 values. determine the minimum numbber of bits required for each word.

  List the state table for the sequential circuit

A sequential circuit with two D flip flops, two inputs x and y, and one output z is specified by the following next state and output equations: A(t + 1) = xy + x'B B(t + 1) = y'A' + yB

  How much modulating signal power is needed to produce

A collector modulated transmitter has a supply voltage of 48 V and an average collector current of 600 mA. What is the input power to the transmitter. How much modulating signal power is needed to produce 100 percent modulation

  Find the coordinates of the particle at a time t later

A charged particle starts from rest at the origin of coordinates in a region where there is a uniform electric field E parallel to the x-axis, and a uniform magnetic flux density B parallel to the z-axis. Show that the coordinates of the particle ..

  Determine synchronous-transient and sub-transient reactances

a. Neglecting resistance, determine the synchronous, transient and sub-transient reactances. b.If the machine is delivering 1.0 p.u. current at 0.8 power factor lagging at the rated terminal voltage when the short circuit is applied.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd