Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. An input signal of 5 sin (2pi 1592t + 0 degrees) is applied to a series RL circuit with resistor R=1000ohm and inductor L=0.1H. The voltage drop across the resistor is? a. 10Vpk angle 90 degrees b. 5Vpk angle 45 degrees c. 3.54 Vpk angle 45 degrees d. 3.54 Vpk angle -45 degrees e. No correct answer listed
2. An input signal of 10 sin (2pi 1592t+0degrees) is applied to a series RC circuit with resistor R =1000ohm and capacitor C= 0.1 uF. The current flow through the capacitor is? a. 10mApk angle 90 degrees b. 5mApk angle 45 degrees c. 7.07mApk angle 45 degrees d. 7.07 mApk angle -45 degrees e. no correct answer listed?
A linear-phase FIR filter should be designed with the ideal magnitude response shown in Figure 1 which represents an narrow band-pass filter. The lower cutoff frequency, fL , is 2,000 Hz, and higher cutoff frequency, fH , is 3,600 Hz.
Design a bandpass filter of 'Sallen and Key' topology and having the following characteristics fo = 3.3 kHz, Q = 2.2
Calculate the current in the output of the source before and after the installation of the new device and The temperature sensor output is a voltage which is equal to the temperature sensed by the sensor. Design an electric circuit which can get th..
A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load
In Mips when you use addi or any other commands in which you use a 16 bit value for a reg. value or address offset what operation is done to check if its is a negative number's two's complement or just a regular binary number
A sequential circuit with three D-type flip-flops Y1Y2Y3, input X and output Z is defined with the following input/output functions: D 1 = X Y 3 + X Y 1 Y 3 D 2 = X ( Y 3 + Y 2 ) + X Y 2 Y 3 D 3 = X Y 3 + Y 2 Y 3 Z = Y3
encounter a sequence of birds while walking in the park. The birds can either be blue (B) or red (R). We let X be the random variable corresponding to the number of birds we encounter until seeing the first blue one.
The continuous-time counterpart to the N-point discrete-time MA filter is the I-interval continuous-time MA filter given by the input/output relationship y(t)=(1/I)*Integral of x(lamda) delta lambda where the bounds are from t-I
The voltage output from a two active gage of Wheatstone bridge was 3.5 mV. The excitation voltage was 5 V. Nominal resistance of the strain gage was 350 ohms and the gage factor was 2.05. Calculate the force in pounds on the steel rod.
The location of the zeroes in the spectrum suddenly changes to 5 kHz, 10 kHz, 15 kHz.... What parameter of the rectangular pulses has changed and what is its new value?
assuming XTAL=11.0592 MHz,write a program to genrate a square wave of 20 Hz frequency on pin2.3?
Determine the source voltage Vs of a 60-Hz power transmission system from the loading conditions described as follows: 1. The load is capacitive and absorbs 12 kW at 240
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd